Honda Civic. Manual — part 239
Fig. 177: Identifying Shift Solenoid Harness Connector Terminal
Courtesy of AMERICAN HONDA MOTOR CO., INC.
8. Measure the shift solenoid valve resistance between the shift solenoid harness
connector terminals below and body ground:
No. 1: Shift solenoid valve C
No. 2: Shift solenoid valve B
No. 5: Shift solenoid valve A
No. 8: Shift solenoid valve D
Standard: 12-25 ohms
If the resistance is within the standard, go to step 9 and check solenoid
valve for a clicking sound.
If the resistance is out of standard, go to step 10.
9. Connect a jumper wire from the battery positive terminal to each shift solenoid
harness connector terminals individually. A clicking sound should be heard.
If a clicking sound is heard, the valves are OK.
The test is complete, connect the connector.
If no clicking sound is heard, go to step 10 and test the shift solenoid
harness.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
10. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
Fig. 178: Identifying Drain Plug w/Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
11. Reinstall the drain plug with a new sealing washer (B).
12. Remove the shift solenoid valve cover (A), the dowel pins (B), the gasket (C),
and the harness clamp bracket (D).
Fig. 179: Identifying Shift Solenoid Valve Cover, Dowel Pins, Gasket,
Harness Clamp Bracket & Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
13. Disconnect the connectors from shift solenoid valve A, shift solenoid valve B,
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
shift solenoid valve C, and shift solenoid valve D.
Fig. 180: Identifying Shift Solenoid Valve
Courtesy of AMERICAN HONDA MOTOR CO., INC.
14. Measure the resistance of each solenoid valve between the connector terminal
and body ground.
Standard: 12-25 ohms
If the resistance is out of standard, go to step 17 and replace the shift
solenoid valve.
If the resistance is within the standard, go to step 15 and check the
solenoid valve for a clicking sound.
15. Connect a jumper wire from the positive battery terminal to each solenoid
terminal individually.
If a clicking sound is heard, go to step 16 and replace the solenoid harness.
If no clicking sound is heard, go to step 17 and replace shift solenoid
valve.
16. Remove the shift solenoid harness connector (A), and replace it. Install a new
O-ring (B) on the shift solenoid harness connector, and install the connector in
the transmission housing, then go to step 22.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Fig. 181: Identifying Shift Solenoid Harness Connector, O-Ring w/Torque
Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
17. Remove the mounting bolts, then hold the shift solenoid valve body and
remove the solenoid valves. Do not hold the connector to remove the solenoid
valve.
Fig. 182: Identifying Shift Solenoid Valve, O-Ring & Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.
18. Install new O-rings (two O-rings per solenoid valve) (E) on the reused solenoid
valve.
2008 Honda Civic LX
2006-08 TRANSMISSION Automatic Transmission - Civic (Except Hybrid)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст