Honda Odyssey (2019 year). Instruction — part 6
80
Safe Driving
Exhaust Gas Hazard
Carbon Monoxide Gas
The engine exhaust from this vehicle contains carbon monoxide, a colorless,
odorless, and highly toxic gas. As long as you properly maintain your vehicle, carbon
monoxide gas will not get into the interior.
■
Have the exhaust system inspected for leaks whenever
• The exhaust system is making an unusual noise.
• The exhaust system may have been damaged.
• The vehicle is raised for an oil change.
When you operate a vehicle with the tailgate open, airflow can pull exhaust gas into
the interior and create a hazardous condition. If you must drive with the tailgate
open, open all the windows and set the climate control system as shown below.
1. Select the fresh air mode.
2. Select the
mode.
3. Set the fan speed to high.
4. Set the temperature control to a comfortable setting.
Adjust the climate control system in the same manner if you sit in your parked
vehicle with the engine running.
1
An enclosed area such as a garage can quickly fill up
with carbon monoxide gas.
Do not run the engine with the garage door closed.
Even when the garage door is open, drive out of the
garage immediately after starting the engine.
3
WARNING
Carbon monoxide gas is toxic.
Breathing it can cause unconsciousness and
even kill you.
Avoid any enclosed areas or activities that
expose you to carbon monoxide.
81
Safe Driving
Safety Labels
Label Locations
These labels are in the locations shown. They warn you of potential hazards that can cause serious injury or death. Read these labels
carefully.
If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact a dealer
for a replacement.
(SAE J639 J2842 J2845)
Sun Visor
U.S. models
Canadian models
Radiator Cap
U.S. models
U.S. models only
Dashboard
Canadian models
Air Conditioner System
82
83
Instrument Panel
This chapter describes the buttons, indicators, and gauges that are used while driving.
Indicators . . . . . . . . . . . 84
Driver Information Interface Warning and
Information Messages. . . . . 102
Gauges. . . . . . . . . . . 119
Driver Information Interface . . . . 120
84
In
strum
e
nt Pa
nel
Indicators
Indicator
Name
On/Blinking
Explanation
Message
Parking Brake
and Brake
System Indicator
(Red)
• Comes on for a few seconds when
you set the power mode to ON,
then goes off if the parking brake
has been released.
• Comes on when the parking brake
is applied, and goes off when it is
released.
• Comes on when the brake fluid
level is low.
• Comes on if there is a problem
with the brake system.
• The beeper sounds and the
indicator comes on if you drive
with the parking brake not fully
released.
• Comes on for about 15 seconds
when you push the electric
parking brake switch with the
power mode in OFF.
• Stays on for about 15 seconds
when you set the power mode to
OFF while the electric parking
brake is set.
• Comes on while driving - Make sure
the parking brake is released. Check the
brake fluid level.
2 What to do when the indicator
• Comes on along with the ABS
indicator - Have your vehicle checked
by a dealer.
2 If the Brake System Indicator (Red)
• Blinks and the brake system
indicator (amber) comes on at the
same time - There is a problem with the
electric parking brake system. The
parking brake may not be set.
Avoid using the parking brake and have
your vehicle checked by a dealer
immediately.
2 If the Brake System Indicator (Red)
Comes On or Blinks at the Same
Time When the Brake System
Indicator (Amber) Comes On P. 721
U.S.
Canada
(Red)
85
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Parking Brake
and Brake
System Indicator
(Amber)
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on if there is a problem
with a system related to braking
other than the conventional brake
system.
• Comes on if there is a problem
with the electric parking brake
system.
• Stays on constantly - Have your
vehicle checked by a dealer.
• Comes on while driving - Avoid using
the parking brake and have your vehicle
checked by a dealer immediately.
• Comes on if there is a problem
with the automatic brake hold
system.
2 Automatic Brake Hold P. 606
U.S.
Canada
(Amber)
U.S.
Canada
U.S.
Canada
86
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Automatic Brake
Hold System
Indicator
• Comes on when the automatic
brake hold system is on.
Automatic Brake
Hold Indicator
• Comes on when the automatic
brake hold is activated.
—
Malfunction
Indicator Lamp
• Comes on when you set the
power mode to ON, and goes off
when the engine starts, or after
several seconds if the engine did
not start. If “readiness codes”
have not been set, it blinks five
times before it goes off.
• Comes on if there is a problem
with the emissions control system.
• Blinks when a misfire in the
engine’s cylinders is detected.
• Readiness codes are part of the on board
diagnostics for the emissions control
systems.
2 Testing of Readiness Codes P. 746
• Comes on while driving - Have your
vehicle checked by a dealer.
• Blinks while driving - Stop in a safe
place where there are no flammable
objects. Stop the engine for 10 minutes
or more, and wait for it to cool down.
Then, take your vehicle to a dealer.
2 If the Malfunction Indicator Lamp
U.S.
Canada
87
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Charging System
Indicator
• Comes on when you set the power
mode to ON, and goes off when
the engine starts.
• Comes on when the battery is not
charging.
• Comes on while driving - Turn off the
climate control system and rear defogger
in order to reduce electricity
consumption.
2 If the Charging System Indicator
Gear Position
Indicator
• Indicates the current gear
selection.
—
M (sequential
mode) Indicator/
Sequential Mode
Gear Selection
Indicator
• Comes on when the manual
sequential shift mode is applied.
2 Sequential Mode P. 552
—
88
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Transmission
System Indicator
• All the gear positions may light for
several seconds, and go off.
• When all the gear positions light,
immediately stop your vehicle in a safe
place.
• Indicators go off if there is no problem.
However, even if they go off, take your
vehicle to a dealer for inspection.
• The indicated current gear
selection blinks if there is a
problem with the transmission
system.
• Avoid sudden start and acceleration, and
stop in a safe place immediately.
Have your vehicle checked by a dealer.
• The current gear position or all the
gear positions blink if there is a
problem with the transmission
system and the vehicle will no
longer move.
• Immediately stop in a safe place.
• Have your vehicle checked by a dealer.
• The current gear position or all the
gear positions blink if you cannot
select
(
P due to a transmission
system failure.
• The engine can be activated as a
temporary measure.
Indicator Blinks along with the
Warning Message P. 723
• Set the parking brake when parking.
• Have your vehicle checked by a dealer
immediately.
89
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Seat Belt
Reminder
Indicator
• Comes on and the beeper sounds
if you are not wearing a seat belt
when you set the power mode to
ON.
• If the front passenger is not
wearing a seat belt, the indicator
comes on a few seconds later.
• Blinks while driving if either you
and/or the front passenger has not
fastened a seat belt. The beeper
sounds and the indicator blinks at
regular intervals.
• The beeper stops and the indicator goes
off when you and the front passenger
fasten their seat belts.
• Stays on after you and/or the front
passenger has fastened the seat
belt(s) - A detection error may have
occurred in the sensor. Have your vehicle
checked by a dealer.
2 Seat Belt Reminder P. 39
Low Fuel
Indicator
• Comes on when the fuel reserve is
running low (approximately 3.6
U.S. gal./13.7 Liter left).
• Blinks if there is a problem with
the fuel gauge.
• Comes on - Refuel your vehicle as soon
as possible.
• Blinks - Have your vehicle checked by a
dealer.
90
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Anti-lock Brake
System (ABS)
Indicator
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• If it comes on at any other time,
there is a problem with the ABS.
• Stays on constantly - Have your
vehicle checked by a dealer. With this
indicator on, your vehicle still has normal
braking ability but no anti-lock function.
2 Anti-lock Brake System (ABS) P. 608
Supplemental
Restraint System
Indicator
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on if a problem with any of
the following is detected:
- Supplemental restraint system
- Knee airbag system
- Side airbag system
- Side curtain airbag system
- Seat belt tensioner
• Stays on constantly or does not come
on at all - Have your vehicle checked by
a dealer.
Auto High-Beam
Indicator
*
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on when all the operating
conditions of the Auto high-beam
are met.
P. 194
—
* Not available on all models
91
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Vehicle Stability
Assist® (VSA®)
System Indicator
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Blinks when VSA® is active.
• Comes on if there is a problem
with the VSA® system, hill start
assist, or brake lighting system.
• Stays on constantly - Have your
vehicle checked by a dealer.
2 Vehicle Stability Assist® (VSA®), aka
Electronic Stability Control (ESC),
System P. 591
2 Hill start assist system P. 543
Vehicle Stability
Assist® (VSA®)
OFF Indicator
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on when you partially
disable VSA®.
—
Electric Power
Steering (EPS)
System Indicator
• Comes on when you set the
power mode to ON, and goes off
when the engine starts.
• Comes on if there is a problem
with the EPS system.
• Stays on constantly or does not
come on at all - Have your vehicle
checked by a dealer.
92
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Low Tire
Pressure/TPMS
Indicator
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on if the tire pressure of
any of the tires becomes
significantly low.
• Comes on while driving - Stop in a
safe place, check tire pressures, and
inflate the tire(s) if necessary.
• Blinks for about one minute, and
then stays on if there is a problem
with the TPMS with Tire Fill Assist,
or when a compact spare tire is
temporarily installed.
• Blinks and remains on - Have your
vehicle checked by a dealer. If the vehicle
is fitted with a compact spare, get your
regular tire repaired or replaced and put
back on your vehicle as soon as you can.
Turn Signal and
Hazard Warning
Indicators
• Blinks when you operate the turn
signal lever.
• Blinks along with all turn signals if
you press the hazard warning
button.
• Does not blink or blinks rapidly - A
turn signal light bulb has blown. Change
the bulb immediately.
2 Replacing Light Bulbs P. 665, 667
—
High Beam
Indicator
• Comes on when the high beam
headlights are on.
—
—
93
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
*1:Canadian models only: Apply and hold the brake pedal before selecting the ON mode.
Indicator
Name
On/Blinking
Explanation
Message
Lights On
Indicator
• Comes on whenever the light
switch is on, or in AUTO
*
when
the exterior lights are on.
• If you set the power mode to
ACCESSORY or VEHICLE OFF while the
lights are on, a chime sounds when the
driver’s door is opened.
—
Fog Light
Indicator
*
• Comes on when the fog lights are
on.
—
—
Immobilizer
System Indicator
• Comes on briefly when you set the
power mode to ON, then goes off.
• Comes on if the immobilizer
system cannot recognize the key
information.
• Blinks - You cannot start the engine. Set
the power mode to VEHICLE OFF
*1
, then
select the ON mode again.
• Repeatedly blinks - The system may be
malfunctioning. Have your vehicle
checked by a dealer.
• Do not attempt to alter this system or
add other devices to it. Electrical
problems can occur.
Security System
Alarm Indicator
• Comes on briefly when you set the
power mode to ON, then goes off.
• Blinks when the security system
alarm has been set.
2 Security System Alarm P. 179
—
Indicator
Indicator
* Not available on all models
94
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
System Message
Indicator
• Comes on along with a beep
when a problem is detected. A
system message on the driver
information interface appears at
the same time.
• While the indicator is on, press the
(home) button to see the message again.
• Refer to the Indicators information in this
chapter when a system message appears
on the driver information interface. Take
the appropriate action for the message.
• The driver information interface does not
return to the normal screen unless the
warning is canceled, or the ENTER
button is pressed repeatedly.
—
Econ Mode
Indicator
• Comes on when you press the
ECON button.
2 ECON Button P. 559
Snow Mode
Indicator
• Comes on when you press the
SNOW button and snow mode is
selected.
2 Intelligent Traction Management
P. 560
Normal Mode
Indicator
• Comes on for a few seconds when
Snow mode is selected, and the
vehicle is powered off, then
restarted.
2 Intelligent Traction Management
P. 560
—
95
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
Auto Idle Stop
Indicator
(Green)
*
• Comes on when Auto Idle Stop is
in operation. The engine
automatically shuts off.
P. 554
—
Auto Idle Stop
System Indicator
(Amber)
*
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Blinks if there is a problem with
the Auto Idle Stop system.
• Blinks - Have your vehicle checked by a
dealer.
• Comes on when Auto Idle Stop
system has been turned off by the
Auto Idle Stop OFF Button.
2 Auto Idle Stop System ON/OFF
P. 554
CRUISE MAIN
Indicator
*
• Comes on when you press the
CRUISE button.
—
CRUISE
CONTROL
Indicator
*
• Comes on if you have set a speed
for cruise control.
—
* Not available on all models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст