Honda Ridgeline. Manual — part 215
01
02
03
04
SJC8A00E10411412282KCAT00
14-245
Shift Lever Installation
C
D
E
B
A
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
A
B
C
A
B
C
1. Install the shift lever assembly (A) on the steering
column.
2. Connect the 7P connector (B) to the immobilizer
control unit-receiver.
3. Connect the D3 switch/shift lock solenoid/park pin
switch connector (C), and install the harness clamp
(D) and connector clamp on the bracket (E).
4. Turn the ignition switch to ON (II), and check that
the R position indicator comes on.
5. If necessary, push the shift cable (A) until it stops,
then release it. Pull the shift cable back one step so
that the shift position is in R. Do not hold the shift
cable guide (B) and the damper (C) to adjust the
shift cable.
6. Turn the ignition switch to LOCK (0).
7. Place the shift lever in R, then insert a 6.0 mm
(0.24 in.) pin (A) through the positioning hole (B) on
the shift lever link, and into the positioning hole on
the shift lever bracket. The shift lever (C) is secured
in R.
(cont’d)
05
06
07
14-246
Automatic Transmission
Shift Lever Installation (cont’d)
A
B
C
D
F
G
E
H
I
J
A
B
A
B
C
8. Rotate the socket holder (A) on the shift cable (B) to
place the tab (C) on the holder opposite to the
opening (D) in the socket holder bracket (E). Align
the holder with the opening (F) in the bracket, then
slide the holder into the bracket. Rotate the holder a
quarter turn until the holder lock (G) stops at the
projection (H) to secure the shift cable. Do not
install the shift cable by twisting the shift cable
guide (I) and the damper (J).
9. Install the shift cable end (A) in the shift cable end
holder (B). Keep the shift cable end and end holder
free of grease.
10. Install the new shift cable lock (A) to secure the shift
cable end and shift cable end holder, then slide the
lock tab (B) toward the shift lever link until it stops
to lock the joint (C).
11. Remove the 6.0 mm (0.24 in.) pin that was installed
to hold the shift lever.
12. Move the shift lever to each position, and check
that the A/T gear position indicator follows the
transmission range switch.
13. Install the steering column covers (see page 17-26).
14. Install the driver’s dashboard lower cover
(see page 20-83).
*01
SJC8A00E10411412282MFAT00
14-247
Shift Lever Disassembly/Reassembly
CONNECTOR
CLAMP
SHIFT LOCK SOLENOID
PLUNGER SPRING
SHIFT LOCK SOLENOID PLUNGER
SHIFT LOCK RELEASE PIN
RELEASE PIN SPRING
SHIFT LOCK RELEASE
D3 SWITCH
SHIFT LEVER KNOB
SCREW
3 N·m
(0.3 kgf·m, 2 lbf·ft)
SELF-LOCKING NUTS
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
SHIFT LEVER
POSITION GUIDE
HARNESS
CLAMP
SHIFT LEVER
BRACKET
SELF-LOCKING NUTS
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
WASHER
SHIFT LEVER LINK
D3 SWITCH/
SHIFT LOCK SOLENOID/
PARK PIN SWITCH
CONNECTOR
SHIFT LEVER
LINK BUSHING
HARNESS
CLAMP
HARNESS
CLAMP
D3 SWITCH
HARNESS
SHIFT LOCK STOP/
STOP CUSHION
ASSEMBLY
PARK PIN SWITCH
SHIFT LEVER
KNOB RING
Apply silicon grease to movable joints.
Apply non-hardening
thread lock sealant.
Replace.
Replace.
01
02
03
04
SJC8A00E10411412284KBAT00
14-248
Automatic Transmission
Shift Lever Bracket Assembly Replacement
A
B
C
D
A
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
C
D
A
B
C
A
B
C
D
E
A
1. Remove the shift lever assembly (see page 14-243).
2. Remove the harness clamps from the shift lever
bracket, and remove the harnesses from the
harness clamps.
3. Pry up the lock covers (A) of the D3 switch/shift lock
solenoid/park pin switch connector (B).
4. Remove the terminal from the connector by
pushing the lock tab (C) up in the connector using a
thin blade screwdriver (D). Remove all six terminals,
and replace the connector.
5. Remove the self-locking nut (A) securing the shift
lever link (B) and washer (C), and remove the shift
lever link. Do not drop and lose the shift lever link
bushing (D).
6. Remove the shift lock release pin (A), spring (B),
and shift lock release (C).
7. Remove the shift lock the solenoid (A), the solenoid
plunger (B), and the plunger spring (C) while prying
up the solenoid lock (D).
8. Remove the shift lock the stop and the stop cushion
assembly (E).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст