Honda Ridgeline. Manual — part 216
05
06
07
08
14-249
A
3 N·m
(0.3 kgf·m,
2 lbf·ft)
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
9. Remove the park pin switch (A).
10. Remove the self-locking nuts, and remove the shift
lever position guide (A) from the shift lever bracket.
11. Pry off the shift lever knob ring (A), and remove it.
12. Unlatch the D3 switch harness clamp on the shift
lever bracket, pry out the D3 switch (B), and pull it
from the knob.
13. Remove the D3 switch harness terminals by prying
the lock tabs up with a thin blade screwdriver.
(cont’d)
Replace.
09
10
11
12
14-250
Automatic Transmission
Shift Lever Bracket Assembly Replacement (cont’d)
A
14. Pull the D3 switch harness wires gently from shift
lever bracket side, and remove the harness wires
and tube. Remove the D3 switch harness clamp (A).
15. Remove the shift lever knob from the shift lever.
16. Replace the shift lever bracket.
17. Install the shift lever knob on a new shift lever.
18. Apply silicone grease to the opening detent of the
shift lever position guide, and install the shift lever
position guide with new self-locking nuts on the
shift lever bracket.
19. Shift the shift lever into P.
20. Insert a wire into the shift lever end, pass it through
the shift lever, then pull the wire out.
21. Wrap the D3 switch terminals with tape, and tie a
string around the switch terminals.
22. Pull the wire from the shift lever end, and pull the
D3 switch harness terminals out of the shift lever
end.
23. Remove the wire and tape.
24. Install the D3 switch harness terminals in the D3
switch. Either harness terminal can be installed in
either cavity.
13
14
14-251
C
B
A
A
B
C
D
E
E
25. Install the D3 switch (A) in the shift lever knob (B).
26. Install the shift lever knob ring (C).
27. Insert the D3 switch harness wires (connector side)
through the shift lever into the hole behind the shift
lock solenoid.
28. Install the park pin switch by aligning the tab with
the positioning hole on the shift lever position
guide. Apply non-hardening thread lock sealant to
the screw, then secure the park pin switch with the
screw.
29. Apply silicone grease to the pin on the shift lever
bracket, and install the shift lock stop over the pin.
30. Install the shift lock solenoid plunger and the
plunger spring in the shift lock solenoid.
31. Apply silicone grease to the tip of the shift lock stop,
and install the shift lock solenoid by aligning the
joint of the shift lock solenoid plunger with the tip
of the shift lock stop.
32. Apply silicone grease to the shift lock release pin
and spring, and install the shift lock release, spring,
and pin.
33. Apply silicone grease to the sliding areas between
the shift lever link and the shift lever bracket.
34. Apply silicone grease to the shift lever link bushing,
and install the bushing in the shift lever link.
35. Install the shift lever link with installing the shift
lever pin into the shift lever link bushing.
36. Apply silicone grease to seating area of the washer
on the shift lever link, and install the washer and
the new self-locking nut.
37. Install the RED harness terminal (A) of the shift lock
solenoid in the No. 5 cavity, and the BLK harness
terminal (B) in the No. 6 cavity.
38. Install the D3 switch harness terminals (WHT) (C) in
the No. 3 and No. 4 cavities. Either D3 switch
harness terminal can be installed in the No. 3 and
No. 4 cavities.
39. Install the park pin switch harness terminals (BLK)
(D) in the No. 1 and No. 2 cavities. Either park pin
switch harness terminal can be installed in the
No. 1 and No. 2 cavities.
40. Make sure that all six terminals lock securely, then
install the lock covers (E) securely in place.
(cont’d)
Terminal side of male terminals
15
16
14-252
Automatic Transmission
Shift Lever Bracket Assembly Replacement (cont’d)
A
B
C
A
B
C
D
E
B
41. Install the D3 switch harness clamp (A), then install
the harness (B) in the clamp at the mark (C).
42. Route the harnesses (A) through the guides (B).
43. Align the marks (C) on each harness, and tie the
harness together into bundle with a new harness
clamp (D) over the marks.
44. Tie the harness together into bundle with a new
harness clamp, then install the harness clamp (E)
on the shift lever bracket.
45. Install the shift lever assembly (see page 14-245).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст