Honda Ridgeline. Manual — part 351
02
03
20-42
Glass
Rear Window Middle Glass Regulator Replacement (cont’d)
Fastener Locations
: Bolt, 2
C
: Bolt, 3
D
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
C
D
E
C
D
D
F
E
A
3. Disconnect the connector (A) from the regulator
motor (B).
4. Remove the bolts (C, D), and detach the cable clips
(E), then remove the regulator (F) and motor.
5. Apply multipurpose grease to the sliding surfaces
of the regulator (A) where shown.
6. Install the regulator in the reverse order of removal,
and note these items:
• Slide the glass right and left to see if it moves
freely without binding.
• Make sure the connector is plugged in properly.
01
02
03
SJC8A00J54400050473KBAT00
20-43
Rear Window Middle Glass Replacement
Fastener Locations
: Bolt, 2
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
C
D
D
A
B
NOTE:
• Put on gloves to protect your hands.
• Take care not to bend or scratch the trim and panels.
1. Remove these items:
• Rear seat-back (see page 20-119)
• Rear trim panel (see step 2 on page 20-68)
2. Remove the rear window middle glass mounting
bolts.
3. Open the middle glass (A) fully by hand. Insert a
pick tool (B) to the glass run channel (C) as shown,
and pull out the edge of the upper spacer (D), and
then pull out the spacer by hand from between the
glass run channel and glass.
4. Move the glass (A) until you can remove it as
shown. Pull up the glass to release the bottom of
the glass, and pull out the top of the glass from the
glass run channel (B), and then remove the glass.
5. Install the glass in the reverse order of removal,
and note these items:
• Make sure the spacer is installed properly.
• Slide the glass to see if it moves freely without
binding.
• Make sure that there is no clearance between the
glass and glass run channel when the glass is
closed.
• Check for water leaks (see step 7 on page 20-23).
• Test-drive, and check for wind noise and rattles.
01
02
03
SJC8A00J54400030071KBAT00
20-44
Glass
Rear Window Glass Run Channel Replacement
A
D
B
C
A
A
D
D
A
B
C
B
B
B
A
A
C
C
C
NOTE:
• Put on gloves to protect your hands.
• Take care not to bend or scratch the trim and panels.
1. Remove these items:
• Rear seat-back (see page 20-119)
• Rear trim panel (see step 2 on page 20-68)
• Rear window middle glass (see page 20-43)
2. Carefully cut the glass run channel (A) on the
middle glass areas (B) with a utility knife (C), and
then pull out the glass run channel from the top and
bottom groove areas of the rear window molding
(D). Take care not to damage the molding.
3. Check the molding for damage, and replace the
rear window if necessary.
4. With a knife, scrape the remaining glass run
channels (A) from the grooves (B) on the middle
glass areas of the rear window molding (C).
5. Clean the molding bonding surface with a sponge
dampened in isopropyl alcohol. After cleaning,
keep oil, grease and water from getting on the
clean surface.
6. Apply a light coat of primer to the groove areas (A)
of the rear window molding (B). Install the glass
run channel (C) to the top and bottom groove areas
of the molding, and then attach the glass run
channel to the middle glass areas of the molding
with adhesive (3M DP8005).
7. Scrape or wipe the excess adhesive off with a soft
shop towel dampened with alcohol.
8. Reinstall the removed parts.
*01
SJC8AB9J34200000000DAAT01
20-45
Moonroof
Component Location Index
FRONT DRAIN VALVE
FRONT DRAIN TUBE
FRAME
SEALS
FRAME
REAR DRAIN TUBE ASSEMBLY
REAR DRAIN
VALVE
SLIDE STOP
DRAIN CHANNEL SLIDER
CABLE ASSEMBLY
SUNSHADE
WIND DEFLECTOR
REAR CENTER
DRAIN TUBE
CABLE TUBE REAR BRACKET
LIMIT SWITCH
BRACKET COVER
DRAIN CHANNEL
GLASS
MOTOR
DEFLECTOR
BASE
Replacement, page 20-52
Replacement, page 20-52
Replacement,
page 20-52
Replacement,
page 20-55
Replacement, page 20-55
Replacement,
page 20-50
Replacement,
page 20-48
Adjustment, page 20-57
Replacement, page 20-49
Position Adjustment, page 20-47
Replacement, page 20-47
Closing Force and Opening Drag Check, page 20-58
Replacement,
page 20-51
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст