Honda Ridgeline. Manual — part 352
![](/vehicles/vescileif/meyomestay/ben/chas.png)
SJC8AB9J34200000000HBAT01
Symptom
Diagnostic procedure
Also check for
20-46
Moonroof
Symptom Troubleshooting Index
Water leaks from moonroof
1.
2.
3.
4.
Check for a clogged drain tube.
Check for a gap between the glass weatherstrip and the roof
panel.
Check for a defective or an improperly installed glass
weatherstrip or drain channel.
Check for a gap between the drain seal and the roof panel.
Wind noise from moonroof
Check for excessive clearance between the glass weatherstrip and
the roof panel.
Motor noise from
moonroof
1.
2.
3.
Check for a loose motor.
Check for a worn gear or bearing.
Check for a deformed cable assembly.
Moonroof glass does not
move, but motor turns
1.
2.
3.
4.
Check for a defective gear or inner cable.
Check for foreign matter stuck between the guide rail and the
slider.
Check for a loose inner cable.
Make sure the cable assembly is attached properly.
Moonroof glass does not
move and motor does not
turn (glass can be moved
with 5 mm hexagonal
wrench)
1.
2.
3.
4.
5.
6.
Check for a blown fuse.
Check for a faulty moonroof switch.
Check the limit switch.
Check for a run down battery.
Check for a defective motor.
Check for a faulty relay.
![](/vehicles/vescileif/meyomestay/ben/thasny.png)
+ −
+
−
01
02
SJC8AB9J34200040901MBAT00
01
02
SJC8AB9J34200040901KBAT00
±
±
20-47
20-47
Glass Position Adjustment
Glass Replacement
0.3
1 mm
(0.01
0.04 in.)
A
B
Forward
A
5 x 0.8 mm
3.9 N·m (0.4 kgf·m, 3 lbf·ft)
Fastener Locations
: Bolt, 6
Fastener Locations
: Screw, 2
B
: Bolt, 6
E
5 x 0.8 mm
3.9 N·m
(0.4 kgf·m,
3 lbf·ft)
Forward
A
B
C
D
E
F
C
D
E
E
A
The roof panel (A) should be even with the glass
weatherstrip (B), to within 0.3
1/
1 mm (0.01
0.04/
0.04 in.) all the way around. If not, make the following
adjustment:
1. Slide the sunshade all the way back.
2. Remove the bracket cover.
3. With a TORX T25 bit, loosen the bolts on each side,
and adjust the glass (A).
4. If necessary, repeat on the opposite side.
1. Close the glass fully.
2. Slide the sunshade all the way back.
3. Pry out the cap (A), remove the screw (B), release
the hooks (C), and remove the bracket cover (D).
Repeat on opposite side. Use a TORX T25 bit to
remove the bolts (E) from the glass brackets (F) on
both sides.
4. Remove the glass (A) by lifting it up. Do not
damage the roof panel.
5. Install the glass in the reverse order of the removal,
and adjust the glass position alignment.
6. Check for water leaks. Use free-flowing water from
a hose without a nozzle. Do not use high-pressure
water.
NOTE: It is normal for some water to seep past the
moonroof into the moonroof frame and exit
through the drains.
![](/vehicles/vescileif/meyomestay/ben/yoru.png)
01
02
03
SJC8AB9J34200041551KBAT00
20-48
Moonroof
Wind Deflector Replacement
A
A
B
C
A
1. Open the glass fully.
2. Remove the links (A) from both sides.
3. Remove the wind deflector (A).
4. Pry up on the deflector bases (A) and release the
hooks (B), then remove the bases with springs (C)
from both sides.
5. Install the deflector in the reverse order of removal.
![](/vehicles/vescileif/meyomestay/ben/befo.png)
01
02
03
SJC8AB9J34200040701KBAT00
20-49
Drain Channel Replacement
A
B
A
B
A
A
C
1. Fully close the moonroof, then place it in the full
tilt-up position.
2. Remove the glass (see page 20-47).
3. Disconnect the rod clips (A), then remove the drain
channel rods (B) on both sides.
4. Slide the drain channel (A) forward.
5. Pull the rear edge of the drain channel (A) up while
pushing both clips (B), and release the channel
from both hooks (C) of the drain channel slider by
pulling it rearward.
6. Remove the drain channel.
7. Install the channel in the reverse order of removal,
and note these items:
• Push the clip portions into place securely.
• Check the glass position adjustment (see page
20-47).
8. Check for water leaks. Let the water run freely from
a hose without a nozzle. Do not use a high-pressure
spray.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст