Honda Ridgeline. Manual — part 386
*01
SJC8A00J18533232001DAAT00
20-182
Openers
Component Location Index
IN-BED TRUNK LID LOCK CYLINDER
IN-BED TRUNK LID OPENER
FUEL FILL DOOR LATCH
IN-BED TRUNK LID LATCH
FUEL FILL DOOR OPENER CABLE
FUEL FILL DOOR OPENER
HOOD RELEASE HANDLE
HOOD LATCH
HOOD OPENER CABLE
Replacement, page 20-190
Replacement, page 20-188
Replacement, page 20-184
Replacement, page 20-187
Replacement, page 20-184
Replacement, page 20-186
Replacement, page 20-183
Replacement, page 20-185
Replacement, page 20-183
01
SJC8A00J18533232001KBAT00
20-183
Hood Opener Cable Replacement
Fastener Locations
C
: Bolt, 2
E
: Clip, 5
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
B
C
D
E
F
E
E
E
E
C
A
E
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the body and related parts.
1. Remove these items:
• Front bulkhead cover (see page 20-171)
• Front inner fender, left side as needed (see page 20-178)
• Kick panel, left side (see page 20-60)
2. Disconnect the hood opener cable (A) from the hood latch (B) (see page 20-185).
3. Remove the bolts (C), then remove the hood release handle (D).
4. Using a clip remover, detach the clips (E), and remove the grommet (F) from the body, then remove the hood
opener cable from the vehicle. Take care not to kink the cable.
5. Install the cable in the reverse order of removal, and replace any damaged clips.
01
02
03
SJC8A00J18526327912KBAT00
20-184
Openers
Fuel Fill Door Opener Cable Replacement
Fastener Locations
: Clip, 3
A
B
C
Fastener Locations
: Clip, 3
A
B
B
A
B
SRS components are located in this area. Review the
SRS component locations (see page 24-14) and the
precautions and procedures (see page 24-16) before
doing repairs or service.
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the body and related parts.
1. Remove these items from the left side of the
vehicle:
• Front door sill trim (see page 20-60)
• Rear door sill trim (see page 20-60)
• B-pillar lower trim (see page 20-65)
• Rear seat side trim (see page 20-60)
• Rear fender cover (see page 20-181)
• Side bed panel (see page 20-162)
2. Disconnect the fuel fill door opener cable from the
fuel fill door opener (see page 20-186).
3. Remove the fuel fill door opener cable (A) from the
clips, and remove the urethane block (B) from the
body, then remove the grommet (C).
4. From the left rear wheel arch, detach the clips, and
then pull out the fuel fill door opener cable (A), and
remove the grommets (B).
5. On the pickup bed, remove the fuel fill door latch
(A) from the body by turning it 90 °, then remove
the fuel fill door opener cable (B) by pulling out
through the hole in the body. Take care not to kink
the cable.
04
01
02
SJC8A00J18533231801KBAT00
20-185
20-185
Hood Latch Replacement
A
B
A
B
Fastener Locations
: Bolt, 3
A
: Nut, 1
B
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
A
A
6. Install the opener cable (A) in the reverse order of
removal, and note these items:
• Check if the clips are damaged or stress-
whitened, and if necessary, replace them with
new ones.
• Align the mark (B) on the cable with the clips.
NOTE:
• Put on gloves to protect your hands.
• Take care not to scratch the body.
1. Remove the front bulkhead cover (see page 20-171).
2. Detach the latch switch connector (A) from the
connector clip (B), and disconnect it.
3. Remove the bolts (A) and nut (B), then remove the
latch (C) from the body.
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст