Honda Ridgeline. Manual — part 269
01
01
01
01
01
01
01
01
01
01
SJC8A000000000J1601PAAT00
Ref. No.
Tool Number
Description
Qty
16-2
Driveline/Axle
Special Tools
071AF-S3VA100
Ball Joint Thread Protector, 14 mm
1
07JAD-PH80101
Oil Seal Driver Attachment
1
07LAF-SM40300
Support Base Attachment
1
07MAC-SL0A202
Ball Joint Remover, 28 mm
1
07XAC-001020A
Threaded Adapter, 24 x 1.5 mm
1
07XAC-001030A
Threaded Adapter, 26 x 1.5 mm
1
07746-0010300
Attachment, 42 x 47 mm
1
07749-0010000
Driver
1
07947-4630100
Fork Seal Driver, 39.2 x 49.5 x 15 mm
1
07965-SD90100
Support Base
1
07AAD-S9VA000
Driveshaft Remover
1
,
*01
SJC8A00E16266500000DAAT00
16-3
Component Location Index
PROPELLER SHAFT
FRONT DRIVESHAFT
INTERMEDIATE SHAFT
REAR DRIVESHAFT
Inspection, page 16-39
Removal, page 16-40
Installation, page 16-41
Inspection, page 16-4
Removal, page 16-4
Disassembly, page 16-6
Reassembly, page 16-10
Installation, page 16-17
Removal, page 16-19
Disassembly, page 16-19
Reassembly, page 16-21
Installation, page 16-24
Inspection, page 16-4
Removal, page 16-24
Disassembly, page 16-27
Reassembly, page 16-30
Installation, page 16-36
01
SJC8A00E16226600000MAAT01
01
SJC8A00E16226600000KAAT02
Special Tools Required
16-4
16-4
Driveline/Axle
Driveshaft Inspection
Front Driveshaft Removal
E
A
C
B
D
E
A
B
1. Check the inboard boot (A) and the outboard boot
(B) on the driveshaft (C) for cracks, damage, leaking
grease, and loose boot bands (D). If any damage is
found, replace the boot and boot bands.
2. Turn the driveshaft by hand, and make sure the
splines (E) and joint are not excessively loose.
3. Make sure the driveshaft is not twisted, bent, or
cracked; if it is, replace it.
Ball joint thread protector, 14 mm 071AF-S3VA100
1. Raise the front of the vehicle, and support it with
safety stands in the proper locations (see page
1-10).
2. Remove the wheel nuts and front wheels.
3. Lift up the locking tab (A) on the spindle nut (B),
then remove, and discard the nut.
4. If you need to remove the left driveshaft, drain the
transmission fluid (see step 3 on page 14-210). It is
not necessary to drain the transmission fluid when
the right driveshaft is removed.
02
03
04
05
Left driveshaft:
Right driveshaft:
16-5
A
B
C
A
B
A
B
5. Remove the lock pin (A) from the lower arm ball
joint castle nut (B), and remove the nut (see page
18-14).
NOTE:
• To avoid damaging the ball joint, install the ball
joint thread protector onto the threads of the ball
joint.
• Be careful not to damage the ball joint boot when
installing the remover.
6. Separate the ball joint from the lower arm (C) with
the special tool (see step 1 on page 18-12).
7. Pull the knuckle outward, and remove the
driveshaft outboard joint from the front wheel hub
using a plastic hammer.
8. Pry (left driveshaft)/tap (right driveshaft) the
inboard joint (A), and remove the driveshaft from
the differential case or bearing support as an
assembly. Do not pull on the driveshaft (B); the
inboard joint may come apart. Pull the driveshaft
straight out to avoid damaging the differential oil
seal or the intermediate shaft outer seal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст