Honda Ridgeline. Manual — part 50
01
01
SJC8A000000000J0801PAAT00
Ref. No.
Tool Number
Description
Qty
8-2
Engine Lubrication
Special Tools
07HAA-PJ70100
Oil Filter Wrench
1
070AD-RCAA100
Oil Seal Driver, 64 mm
1
*01
SJC8A00A32200000000DAAT00
8-3
Component Location Index
OIL PRESSURE SWITCH
OIL CONTROL
ORIFICES
O-RINGS
CONNECTING
TUBE
OIL FILTER
OIL PUMP
DRAIN BOLT
WASHER
OIL PAN
DOWEL PINS
BAFFLE PLATE
O-RING
O-RING
OIL SCREEN
OIL FILTER
FEED PIPE
O-RING
ROCKER ARM OIL
CONTROL SOLENOID
(VTEC SOLENOID VALVE)
FILTER
ROCKER ARM OIL
CONTROL SOLENOID
(VTEC SOLENOID VALVE)
ASSEMBLY
Test, page 8-5
Oil Pressure Test, page 8-6
Replacement, page 8-5
Replacement,
page 8-7
Removal, page 8-10
Inspection, page 8-11
Installation, page 8-12
Removal, page 7-11
Installation, page 7-28
Replacement,
page 8-8
SJC8A00A32200000000HBAT01
Symptom
Diagnostic procedure
Also check for
8-4
Engine Lubrication
Symptom Troubleshooting Index
Excessive engine oil consumption
1.
2.
3.
4.
5.
Check the loose of the engine oil fill cap, oil drain
bolt, and oil filter.
Check for oil leaks.
Check for worn valve guide(s) (see page 6-41) or
worn valve stem seal(s) (see page 6-41).
Check for damaged or worn piston ring(s)
(see page 7-21).
Check for damaged or worn engine internal parts
(cylinder wall, pistons, etc.) (see page 7-15).
Low oil pressure indicator does not
come on with the ignition switch
ON (II)
1.
2.
Do the gauge control module self-diagnostic
function (see page 22-244).
Test the oil pressure switch (see page 8-5).
An open in the
wire between the
gauge control
module and the oil
pressure switch
Low oil pressure indicator stays on
1.
2.
3.
4.
5.
6.
7.
8.
Check the engine oil level.
Do the gauge control module self-diagnostic
function (see page 22-244).
Test the oil pressure switch (see page 8-5).
Check the engine oil pressure (see page 8-6).
Check the oil filter for clogging.
Check the oil screen for clogging.
Check the relief valve.
Test the oil pump (see page 8-11).
A wire shorted to
ground between
the gauge control
module and the oil
pressure switch
01
SJC8A00A32200043461FEAT01
01
SJC8A00A32200043461KBAT00
8-5
8-5
Oil Pressure Switch Test
Oil Pressure Switch Replacement
A
C
B
18 N·m
(1.8 kgf·m, 13 lbf·ft)
1. Remove the BLU/YEL wire (A) from the engine oil
pressure switch (B).
2. Check for continuity between the positive terminal
(C) and the engine (ground). There should be
continuity with the engine stopped. There should
be no continuity with the engine running.
1. Disconnect the oil pressure switch connector, then
remove the oil pressure switch.
2. Remove any old liquid gasket from the switch and
switch mounting hole.
3. Apply a very small amount of liquid gasket to the
oil pressure switch threads, then install the oil
pressure switch.
NOTE: Using too much liquid gasket may cause
liquid gasket to enter the oil passage or the end of
the new oil pressure switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст