Honda Ridgeline. Manual — part 51
01
SJC8A00A32200000000FEAT02
01
02
SJC8A00A32200043701KBAT01
Engine Oil Temperature: 176 °F (80 °C)
Engine Oil Pressure:
At Idle:
70 kPa (0.7 kgf/cm , 10 psi) min.
At 3,000 rpm: 490 kPa (5.0 kgf/cm , 71 psi) min.
Capacity
At Oil Change:
4.0 L (4.2 US qt)
At Oil Change including Filter:
4.3 L (4.5 US qt)
After Engine Overhaul:
5.0 L (5.3 US qt)
2
2
8-6
8-6
Engine Lubrication
Oil Pressure Test
Engine Oil Replacement
A
A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
B
If the low oil pressure indicator stays on with the engine
running, check the engine oil level. If the oil level is
correct:
1. Remove the engine oil pressure switch, then install
an oil pressure gauge (A).
2. Start the engine. Shut it off immediately if the
gauge registers no oil pressure. Repair the problem
before continuing.
3. Allow the engine to reach operating temperature
(fan comes on at least twice). The pressure should
be:
4. If oil pressure is out of specifications, inspect these
items:
• Inspect the oil pressure relief valve (see page 8-9).
• Check the oil screen for clogging.
• Inspect the oil pump (see page 8-11).
1. Warm up the engine.
2. Remove the drain bolt (A), and drain the engine oil.
3. Reinstall the drain bolt with a new washer (B).
4. Refill with the recommended oil (see page 3-2).
5. Run the engine for more than 3 minutes, then check
for oil leakage.
Do not overtighten.
01
02
SJC8A00A32200043301KBAT02
Special Tools Required
Tighten:
3/4 Turn Clockwise
Tightening Torque:12 N·m (1.2 kgf·m, 8.7 lbf·ft)
8-7
Engine Oil Filter Replacement
A
B
07HAA-PJ70100
Oil filter wrench 07HAA-PJ70100
1. Remove the oil filter with the oil filter wrench.
2. Inspect the filter to make sure the rubber seal is not
stuck to the oil filter seating surface of the engine.
3. Inspect the threads (A) and rubber seal (B) on the
new filter. Clean the seat on the engine block, then
apply a light coat of new engine oil to the filter
rubber seal. Use only filters with a built-in bypass
system.
4. Install the oil filter by hand.
5. After the rubber seal seats, tighten the oil filter
clockwise with the oil filter wrench.
(cont’d)
▼
▼▼▼▼
▼
▼▼▼▼
▼
▼▼
▼▼▼ ▼▼▼▼
▼▼▼▼
▼
▼▼
▼▼▼
03
01
02
SJC8A00A32200043311KBAT00
8-8
8-8
Engine Lubrication
Engine Oil Filter Replacement
(cont’d)
Oil Filter Feed Pipe Replacement
A
6. If four numbers or marks (1 to 4 or
to
)
are printed around the outside of the filter, you can
use the following procedure to tighten the filter.
• Spin the filter on until its seal lightly seats against
the block, and note which number or mark is at
the bottom.
• Tighten the filter by turning it clockwise three
numbers or marks from the one you noted. For
example, if mark
is at the bottom when the
seal is lightly seated, tighten the filter until the
mark
comes around to the bottom.
Number or
Mark when
rubber seal
is seated
1
or
2
or
3
or
4
or
Number or
Mark after
tightening
4
or
1
or
2
or
3
or
7. After installation, fill the engine with oil up to the
specified level, run the engine for more than
3 minutes, then check for oil leakage.
1. Remove the filter (see page 8-7).
2. Remove the oil filter feed pipe.
3. Install two 20 x 1.5 mm nuts (A) onto the new oil
filter feed pipe, and hold one nut with a wrench,
then tighten the other nut.
4. Tighten the oil filter feed pipe to 49 N·m (5.0 kgf·m,
36 lbf·ft), then remove the nuts from the oil filter
feed pipe.
Mark when rubber seal
is seated.
Mark after tightening.
01
SJC8A00A32200043502LAAT00
Exploded View
8-9
Oil Pump Overhaul
CRANKSHAFT
OIL SEAL
O-RING
6 x 1.0 mm
6 N·m
(0.6 kgf·m, 4 lbf·ft)
PUMP COVER
OUTER ROTOR
INNER ROTOR
PUMP HOUSING
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
SEALING BOLT
38 N·m
(3.9 kgf·m, 28 lbf·ft)
SPRING
RELIEF VALVE
DOWEL PINS
(cont’d)
Replace.
Replace.
Apply liquid gasket
to the mating surface of
the engine block
when installing.
Valve must slide freely
in the housing bore.
Replace if it is scored.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст