Honda Ridgeline. Manual — part 354
08
09
20-54
Moonroof
Frame and Drain Tube Replacement (cont’d)
A
B
A
Upward
11. To remove the rear drain valve (A), tie a string to
the end of the drain tube (B), then pull the drain
tube down through the C-pillar.
12. Install the frame and drain tube in the reverse order
of removal, and note these items:
• Before installing the frame, clear the drain tubes
and drain valves using compressed air.
• When installing a drain tube, tie the string that
was pulling through the pillar during the
disassembly to the top end of the new drain tube,
pull it up through the pillar to the moonroof
frame.
• Check the frame seal.
• Clean the surface of the frame.
• When installing the frame, first attach the rear
hooks into the body holes.
• Make sure the connectors are plugged in
properly.
• When connecting the drain tube, slide it over the
frame nozzle at least 10 mm (0.39 in.).
• Install the tube clip (A) on the drain tube (B) as
shown.
• Make sure the clips are not rubbing on any parts
or body panels.
13. Check for water leaks. Let the water run freely from
a hose without a nozzle. Do not use a high-pressure
spray.
01
02
SJC8AB9J34200040702KBAT00
20-55
Drain Channel Slider and Cable Assembly Replacement
Fastener Locations
: Screw, 2
A
: Screw, 2
B
: Bolt, 2
E
: Screw, 2
F
A
B
C
D
E
F
G
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
Forward
C
D
E
C
C
A
B
1. Remove the frame (see page 20-52).
2. Remove these parts from the frame:
• Sunshade (see page 20-50)
• Moonroof motor (see page 20-51)
3. Put on gloves to protect your hands. Remove the
screws (A, B) securing the slide stops (C), and cable
tube rear brackets (D), cable tube side bracket
mounting bolts (E) and the cable tube mounting
screws (F) from both sides of the frame (G).
4. Turn both cable tube side brackets (A) up to release
the hooks (B) from the holes in both sides of the
frame.
5. Pivot the glass brackets (C) down by sliding the link
lifters (D) back, then slide both glass brackets back
with the link lifters.
6. Slide the cable assembly (E) half-way.
(cont’d)
03
04
05
20-56
Moonroof
Drain Channel Slider and Cable Assembly Replacement (cont’d)
B
A
A
D
B
C
A
A
B
7. Remove the slide stops (A) and the drain channel
sliders (B) from both sides.
8. Slide the cable assembly (A) and both glass
brackets (B) back, remove the deflector sliders (C)
from both glass brackets, then remove them from
the frame (D).
9. Install the slider and cable assembly in the reverse
order of removal, and note these items:
• Damaged parts should be replaced.
• Apply multipurpose grease to the glass bracket
(A) and guide rail portion of the frame (B)
indicated by the arrows.
• Before reinstalling the motor, make sure both
link lifters are parallel, and in the fully closed
position.
• Before reinstalling the motor, install the frame
and glass, then check the opening drag (see page
20-58).
01
SJC8AB9J34200040951MBAT00
20-57
Limit Switch Adjustment
C
5 x 0.8 mm
5 N·m
(0.5 kgf·m, 4 lbf·ft)
A
B
D
E
F
G
E
1. Remove the headliner (see page 20-70).
2. With the moonroof wrench, close the glass (A) fully:
• Make sure both link lifters (B) are parallel, and in the position shown.
• Check the glass fit to the roof panel and the glass position (see page 20-47).
3. With an open-end wrench, loosen the limit switch mounting bolts (C).
4. Adjust the limit switch (D):
• Move the switch plate (E) a little at a time, then secure it at the position where you hear a faint click when the
switch cam (F) pushes the limit switch (open/close).
• Check that the switch plate contacts the switch bracket (G).
5. Check the operation of the glass (from the tilt-up position to fully closed position, from the fully open position to
the fully closed position) by operating the moonroof switch.
NOTE: Adjust the switch plate until the glass opens and closes correctly.
6. Reinstall all remaining parts in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст