Honda Ridgeline. Manual — part 499
*01
SJC8A00J34300044051DAAT00
22-292
Power Mirrors
Component Location Index
POWER MIRRORS
POWER MIRROR SWITCH
Function Test, page 22-294
Replacement, page 20-27
Power Mirror Actuator Test, page 22-296
Mirror Actuator Replacement, page 22-297
Test/Replacement, page 22-295
*01
SJC8A00J34300000000EAAT00
−
−
−
22-293
Circuit Diagram
J7
A4
G1
BLK/YEL
IG2 HOT in ON (II)
* : RTL, EXL, and LX models
INDICATOR
LIGHT*
(LED)
RED
LIGHT
(0.56W)
RED/BLK
9
4
BLU/WHT
BLK/YEL
BLK/YEL
SWITCH*
DEFOGGER
DOWN
1*
8*
ORN
ORN
ORN
G402
G501
BLK
3*
2*
DEFOGGER*
DEFOGGER*
2*
3*
BLK
GRN/WHT
BLU/BLK
RED/YEL
BLU/WHT
GRN/WHT
GRN/WHT
LEFT MIRROR
RIGHT MIRROR
7
7
8
6
6
8
UP
RIGHT
LEFT
DOWN
DOWN
LEFT
RIGHT
UP
WHT/RED
G501
POWER MIRROR SWITCH
5
2
BLK/YEL
RIGHT
LEFT
UP
6
13
12
11
10
RIGHT
LEFT
LEFT
RIGHT
No.30 (7.5 A)
YEL
IGNITION SWITCH
IG2
BAT
UNDER HOOD FUSE/RELAY BOX
BLK
WHT
No.23 (IG) (50 A)
No.22 (BAT) (120 A)
BATTERY
DASH LIGHTS
BRIGHTNESS
CONTROLLER
(In the gauge
control module)
No.4 (15 A) FUSE
(UNDER HOOD
FUSE/RELAY BOX)
UNDER DASH
FUSE/RELAY BOX
01
SJC8A00J34300000000FEAT00
Both mirrors
Left mirror
Right mirror
Defogger (USA models: RTL, Canada models: LX, EXL)
22-294
Power Mirrors
Power Mirror Switch Function Test
A
B
1. Remove the driver’s door panel (see page 20-7).
2. Disconnect the 13P connector (A) from the power
mirror switch (B), and inspect the terminals. If OK,
go to step 3.
3. Choose the appropriate test based on the
symptom:
• Both mirrors don’t work, go to step 4.
• Left mirror doesn’t work, go to step 6.
• Right mirror doesn’t work, go to step 7.
• Defoggers don’t work, go to step 8.
4. Reconnect the power mirror switch connector, and
check for voltage between the No. 2 terminal and
body ground with the ignition switch ON (II) while
operating the power mirror switch.
There should be battery voltage.
• If there is no battery voltage, check for:
– Blown No. 30 (7.5 A) fuse in the under-dash
fuse/relay box.
– An open in the BLK/YEL wire.
• If there is battery voltage, go to step 5.
5. Check for voltage between the No. 6 terminal and
body ground while operating the power mirror
switch.
There should be less than 1 V.
• If there is more than 1 V, check for:
– An open in the BLK wire.
– Poor ground (G 501).
• If there is less than 1 V, check both mirrors
individually as described in step 6 and 7.
6. Connect the No. 2 terminal to the No. 10 terminal,
and the No. 5 (or No. 12) terminal to body ground
with jumper wires. The left mirror should tilt down
(or swing left) with the ignition switch ON (II).
• If the mirror does not tilt down (or does not swing
left), check for an open in the GRN/WHT (or BLU/
WHT) wire between the left mirror and the 13P
connector. If the wire is OK, check the left mirror
actuator.
• If the mirror neither tilts down nor swings left,
check for an open in the BLU/BLK wire.
• If the mirror works properly, check the mirror
switch.
7. Connect the No. 2 terminal to the No. 11 terminal,
and the No. 5 (or No. 13) terminal to body ground
with jumper wires. The right mirror should tilt
down (or swing left) with the ignition switch ON (II).
• If the mirror does not tilt down (or does not swing
left), check for an open in the GRN/WHT (or WHT/
RED) wire between the right mirror and the 13P
connector. If the wire is OK, check the right
mirror actuator.
• If the mirror neither tilts down nor swings left,
check for an open in the RED/YEL wire.
• If the mirror works properly, check the mirror
switch.
8. Connect the No. 1 and No. 8 terminals with a
jumper wire, and check for voltage between the
No. 1 terminal and body ground. There should be
battery voltage and both mirrors should warm up
with the ignition switch ON (II).
• If there is no voltage or neither warms up, check
for:
– An open in the BLK/YEL and ORN wires.
– Blown No. 30 (7.5 A) fuse in the under-dash
fuse/relay box.
– Poor ground (G 402, G501).
• If only one fails to warm up, check its defogger.
• If both warm up, check the defogger switch.
Wire side of
female terminals
01
02
*01
SJC8A00J34300044041FHAT00
Mirror Switch:
Defogger Switch:
22-295
Power Mirror Switch Test/Replacement
A
B
Terminal
Position
UP
DOWN
LEFT
RIGHT
L
UP
DOWN
LEFT
RIGHT
R
2
5
6
10
11
12
13
Terminal
Position
ON
OFF
1
8
6
1. Disconnect the 13P connector (A) from the power
mirror switch (B).
2. Check for continuity between the terminals in each
switch position according to the table.
3. If the continuity is not as specified, remove the
screws and replace the power mirror switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст