Honda Ridgeline. Manual — part 151
03
04
05
−
−
−
−
YES
NO
YES
NO
11-368
EVAP System
DTC Troubleshooting (cont’d)
PCM CONNECTOR A (44P)
VSV
(LT GRN/RED)
VSV (LT GRN/RED)
EVAP CANISTER VENT SHUT VALVE
2P CONNECTOR
JUMPER WIRE
PCM CONNECTOR A (44P)
VSV
(LT GRN/RED)
12. Jump the SCS line with the HDS.
13. Disconnect PCM connector A (44P).
14. Check for continuity between PCM connector
terminal A10 and body ground.
Repair short in the wire between the EVAP
canister vent shut valve and the PCM (A10), then go
to step 18.
Go to step 15.
15. Connect EVAP canister vent shut valve 2P
connector terminal No. 1 to body ground with a
jumper wire.
16. Check for continuity between PCM connector
terminal A10 and body ground.
Go to step 24.
Repair open in the wire between the EVAP
canister vent shut valve and the PCM (A10), then go
to step 18.
17. Replace the EVAP canister vent shut valve
(see page 11-375).
18. Reconnect all connectors.
Terminal side of female terminals
Wire side of female terminals
Terminal side of female terminals
Is ther e continuity?
Is ther e continuity?
−
−
−
−
YES
NO
YES
NO
11-369
19. Turn the ignition switch ON (II).
20. Reset the PCM with the HDS.
21. Do the PCM idle learn procedure (see page 11-273).
22. Select EVAP CVS ON in the INSPECTION MENU
with the HDS.
23. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EVAP canister vent shut valve and
the PCM, then go to step 1.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
24. Reconnect all connectors.
25. Update the PCM if it does not have the latest
software (see page 11-7), or substitute a known-
good PCM (see page 11-8).
26. Select EVAP CVS ON in the INSPECTION MENU
with the HDS.
27. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EVAP canister vent shut valve and
the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-8), then recheck. If
the PCM was substituted, go to step 1.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-205). If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Is DT C P0498 indicated?
Is DT C P0498 indicated?
SJC8A00K77100090499FAAT30
−
−
DTC P0499:
YES
NO
11-370
EVAP System
DTC Troubleshooting (cont’d)
EVAP Canister Vent Shut Valve
Control Circuit High Voltage
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Select EVAP CVS ON in the INSPECTION MENU
with the HDS.
4. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EVAP canister vent shut valve and
the PCM. If the PCM was updated, substitute a
known-good PCM (see page 11-8), then recheck. If
the PCM was substituted, go to step 1.
If the PCM was updated, troubleshooting is
complete. If the PCM was substituted, replace the
original PCM (see page 11-205). If any other
Temporary DTCs or DTCs are indicated, go to the
indicated DTC’s troubleshooting.
Is DT C P0499 indicated?
−
−
−
01
SJC8A00K77100091454FAAT30
−
−
−
−
−
−
DTC P1454:
DTC P2422:
YES
NO
YES
NO
YES
NO
11-371
A
FTP Sensor Circuit Range/
Performance Problem
EVAP Canister Vent Shut Valve
Close Malfunction
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch OFF.
4. Remove the fuel fill cap, and wait 1 minute.
5. Check the FTP SENSOR in the DATA LIST with the
HDS.
Go to step 6.
Go to step 17.
6. Install the fuel fill cap.
7. Clear the DTC with the HDS.
8. Start the engine. Hold the engine speed at
3,000 rpm without load (in Park on neutral) until the
radiator fan comes on, then let it idle.
9. Monitor the OBD STATUS for DTC P1454 in the
DTCs MENU with the HDS.
Go to step 10.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals at the FTP
sensor, the EVAP canister vent shut valve, and the
PCM. If the screen indicates NOT COMPLETED, go
to step 8 and recheck.
10. Clear the DTC with the HDS.
11. Turn the ignition switch OFF.
12. Remove the EVAP canister vent shut valve from the
EVAP canister (see page 11-375).
13. Connect the 2P connector to the EVAP canister vent
shut valve.
14. Turn the ignition switch ON (II).
15. Select EVAP CVS ON in the INSPECTION MENU
with the HDS.
16. Check the EVAP canister vent shut valve (A)
operation.
Check for a blockage in the EVAP canister,
canister filter, vent hoses, and drain joint, then
install the EVAP canister vent shut valve, and go to
step 23.
Replace the EVAP canister vent shut valve
(see page 11-375), then go to step 23.
(cont’d)
Is it between
0.67 and 0.67 kPa (
0.2 and
0.2 in.Hg,
5 and 5 mmHg), or 2.4 and 2.6 V ?
Does the scr een indicate F AILED?
Does the valve oper ate?
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст