Honda Ridgeline. Manual — part 469
SJC8A00K713000Y1276FAAT10
SJC8A00K713000Y1278FAAT10
−
−
−
−
−
−
−
−
−
−
−
−
DTC B1276:
DTC B1278:
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
22-172
22-172
Exterior Lights
DTC Troubleshooting (cont’d)
Headlight Switch Parking
(SMALL) Position Circuit Malfunction
Headlight Switch ON Position
Circuit Malfunction
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II),
and wait for 2 seconds.
3. Turn the parking (SMALL) light switch ON and wait
for 2 seconds.
4. Turn the headlight switch (LOW) ON and wait for
2 seconds.
5. Change the dimmer switch position from low beam
to high beam and wait for 2 seconds.
6. Check for DTCs with the HDS.
Go to step 7.
Intermittent failure, the headlight switch and
the combination switch control unit are OK at this
time. Check for loose or poor connections at the
headlight switch connector, and at the combination
switch connector.
7. With the headlight switch in the PARKING position,
select LIGHTING SYSTEM with the HDS, and enter
DATA LIST.
8. Check the ON/OFF information of the HEADLIGHT
SWITCH PARKING in the DATA LIST.
Faulty combination switch control unit.
Replace the combination switch.
Go to step 9.
9. Do the headlight switch test (see page 22-181).
Repair the wire between the No. 4 terminal of
the headlight switch 6P connector and the No. 9
terminal of the combination switch 12P
connector.
Replace the headlight switch.
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II),
and wait for 2 seconds.
3. Turn the parking (SMALL) light switch ON and wait
for 2 seconds.
4. Turn the headlight switch (LOW) ON and wait for
2 seconds.
5. Change the dimmer switch position from low beam
to high beam and wait for 2 seconds.
6. Check for DTCs with the HDS.
Go to step 7.
Intermittent failure, the headlight switch and
the combination switch control unit are OK at this
time. Check for loose or poor connections at the
headlight switch connector, and at the combination
switch connector.
7. With the headlight switch in the HEADLIGHT
position, select LIGHTING SYSTEM with the HDS,
and enter DATA LIST.
8. Check the ON/OFF information of the HEADLIGHT
SWITCH ON in the DATA LIST.
Faulty combination switch control unit.
Replace the combination switch.
Go to step 9.
9. Do the headlight switch test (see page 22-181).
Repair the wire between the No. 3 terminal of
the headlight switch 6P connector and the No. 10
terminal of the combination switch 12P
connector.
Replace the headlight switch.
Is DT C B127 6 indicated?
Is the inf or mation indicator ON, and change to
OF F when the headlight switch is put to the OF F
and the HEADLIGHT positions?
Is the headlight switch test OK ?
Is DT C B127 8 indicated?
Is the inf or mation indicator ON, and change to
OF F when the headlight switch is put to the OF F
and the PARK ING positions?
Is the headlight switch test OK ?
SJC8A00K713000Y1279FAAT00
SJC8A00K713000Y1280FAAT00
−
−
−
−
DTC B1279:
DTC B1280:
YES
NO
YES
NO
22-173
22-173
Headlight Switch DIMMER
Position Circuit Malfunction
Turn Signal Switch Circuit
Malfunction
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF and then back ON (II),
then turn the headlight switch ON.
3. Change the dimmer switch from low beam to high
beam and wait for 2 seconds.
4. Pull and hold the dimmer switch lever and keep the
passing switch position for more than 2 seconds.
5. Check for DTCs with the HDS.
Faulty combination switch control unit,
replace the combination switch.
Intermittent failure, the combination switch
control unit is OK at this time. Check for loose or
poor connections at the combination switch
connector.
NOTE: If you are troubleshooting multiple DTCs, be
sure to follow the instructions in B-CAN System
Diagnosis Test Mode A (see page 22-99).
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Turn the turn signal switch to the left turn position
and wait for 2 seconds.
4. Turn the turn signal switch to the right turn position
and wait for 2 seconds.
5. Check for DTCs with the HDS.
Faulty combination switch control unit,
replace the combination switch.
Intermittent failure, the combination switch
control unit is OK at this time. Check for loose or
poor connections at the combination switch
connector.
Is DT C B127 9 indicated?
Is DT C B1280 indicated?
01
SJC8A00J32113314805FEAT00
01
02
SJC8A00J32118616150FEAT00
22-174
22-174
Exterior Lights
Brake Pedal Position Switch Test
Cargo Area Light Switch Test
A
B
B
A
Not used
Terminal
Position
1
2
3
4
OFF
ON
1. Disconnect the 4P connector (A) from the brake
pedal position switch (B).
2. Check for continuity between the No. 1 and No. 2
terminals.
• There should be continuity when the brake pedal
is pressed.
• There should be no continuity when the brake
pedal is released.
3. Check for continuity between the No. 3 and No. 4
terminals.
• There should be no continuity when the brake
pedal is pressed.
• There should be continuity when the brake pedal
is released.
4. If necessary, adjust or replace the switch, or adjust
the pedal height (see page 19-6).
1. Remove the dashboard lower cover (see page
20-83).
2. Push the cargo area light switch (A) from behind
the dashboard lower panel.
3. Check for continuity between the terminals in each
switch position according to the table.
4. If the continuity is not as specified, replace the bulb
(B) or the cargo area light switch.
01
01
*01
SJC8A00J32133131131MBAT00
22-175
Headlight Adjustment
A
A
25 ft (7.5 m)
A
B
A
Headlights become very hot during use; do not
touch them or any attaching hardware immediately
after they have been turned off.
Before adjusting the headlights:
• Park the vehicle on a level surface.
• Make sure the tire pressures are correct.
• The driver or someone who weighs the same should
sit in the driver’s seat.
1. Clean the outer lens so that you can see the center
(A) of the headlights.
2. Park the vehicle in front of a wall or a screen (A).
3. Turn the low beams on.
4. Determine if the headlights are aimed properly.
Vertical adjustment:
Measure the height of the headlights (A). The lights
should reflect 2.1 in (52 mm.) below headlight
height (B).
(cont’d)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст