Honda Element. Manual — part 261

Courtesy of AMERICAN HONDA MOTOR CO., INC.

4. Disconnect the transmission range switch connector.

Fig. 342: Identifying Transmission Range Switch Connector
Courtesy of AMERICAN HONDA MOTOR CO., INC.

5. Remove the transmission range switch.

6. Make sure the selector control shaft is in the N position. If necessary, move the shift lever from the P

position to the N position.

Fig. 343: Identifying Selector Control Shaft Positions
Courtesy of AMERICAN HONDA MOTOR CO., INC.

NOTE:

Do not use the selector control shaft to adjust the shift position. If the
selector control shaft tips are squeezed together it will cause a faulty
signal or position due to play between the selector control shaft and the
switch.

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element

7. Align the cutouts (A) on the rotary-frame with the neutral positioning cutouts (B) on the transmission

range switch (C), then put a 2.0 mm (0.08 in.) feeler gauge blade (D) in the cutouts to hold the switch in
the N position.

Fig. 344: Aligning Cutouts On Rotary-Frame With Neutral Positioning Cutouts On Transmission
Range Switch
Courtesy of AMERICAN HONDA MOTOR CO., INC.

8. Install the transmission range switch (A) gently on the selector control shaft (B) with holding it in the N

position with the 2.0 mm (0.08 in.) blade (C).

Fig. 345: Holding Transmission Range Switch With Blade
Courtesy of AMERICAN HONDA MOTOR CO., INC.

9. Tighten the bolts on the transmission range switch while you continue to hold the N position. Do not

move the transmission range switch when tightening the bolts. Remove the feeler gauge.

NOTE:

Be sure to use a 2.0 mm (0.08 in.) blade or equivalent to hold the switch in
the N position.

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element

Fig. 346: Tightening Transmission Range Switch Bolts With Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.

10. Connect the connector securely, then install the transmission range switch cover (A).

Fig. 347: Identifying Transmission Range Switch Cover With Bolts With Torque Specification
Courtesy of AMERICAN HONDA MOTOR CO., INC.

11. Turn the ignition switch ON (II). Move the shift lever through all positions, and check the transmission

range switch synchronization with the A/T gear position indicator.

12. Check that the engine will start in the P and N positions, and will not start in any other shift lever

position.

13. Check that the back-up lights come on when the shift lever is in the R position.

14. Allow the all four wheels (4WD) or the front wheels (2WD) to rotate freely, then start the engine, and

check the shift lever operation.

D3 SWITCH TEST/REPLACEMENT

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element

1. Remove the center lower cover (see CENTER LOWER COVER REMOVAL/INSTALLATION ).

2. Remove the shift lever console trim (see CENTER LOWER COVER

REMOVAL/INSTALLATION ).

3. Shift the shift lever into the R position.

4. Remove the shift cable insulator (A) from the shift cable (B).

Fig. 348: Identifying Shift Cable Insulator And Shift Cable
Courtesy of AMERICAN HONDA MOTOR CO., INC.

5. Slide the lock tab (A) down on the shift cable end holder (B).

Fig. 349: Sliding Lock Tab
Courtesy of AMERICAN HONDA MOTOR CO., INC.

6. Grasp the shift cable lock (C) in the middle with angle-jaw needle-nose pliers (D), and remove it from the

shift cable end and shift cable end holder. Do not pry the shift cable lock with a screwdriver, it may
damage the shift cable end holder.

2007 Honda Element EX

2007-2008 TRANSMISSION Automatic Transmission - Element