Honda Element. Manual — part 698
![](/vehicles/vescileif/qulerpll/din/ncaked.png)
NO -Go to step 11.
11. Turn the ignition switch OFF.
12. Turn the ignition switch ON (II), and watch the immobilizer indicator.
Does the immobilizer indicator stay on or flash?
YES -Go to the immobilizer system's troubleshooting (see TROUBLESHOOTING ).
NO -Go to step 13.
13. Do the gauge self-diagnostic function without the HDS (see SELF-DIAGNOSTIC FUNCTION ).
Are any indicators flashing?
YES -Go to step 14.
NO -Troubleshoot the gauge control module (see SELF-DIAGNOSTIC FUNCTION ).
14. Turn the ignition switch OFF.
15. Disconnect the HDS from the DLC.
16. Check for continuity between body ground and DLC terminals No. 1 and No. 7 individually.
Fig. 139: Checking Continuity Between Body Ground And DLC Terminals No. 1 And No. 7
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Go to step 17.
NO -Go to step 18.
17. Continue to check for continuity between DLC terminals No. 1 and No. 7 and body ground individually,
while disconnecting these parts, one at a time:
Gauge control module 36P connector
2007 Honda Element EX
2007-2008 ENGINE PERFORMANCE PGM-FI System - Element
![](/vehicles/vescileif/qulerpll/din/soneerom.png)
SRS unit connector A (28P)
VSA modulator-control unit 47P connector
Immobilizer control unit 7P connector
TPMS control unit connector B (20P)
Fig. 140: Checking Continuity Between DLC Terminals No. 1 And No. 7 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Does continuity go away when one of the above components is disconnected?
YES -Replace the part that caused an open when it was disconnected.
NO -Repair short in the wire between the DLC No. 7 (K-line) and the VSA modulator-control unit, the
SRS unit, the TPMS control unit, or the gauge control module, or DLC No. 1 (DIAG-H line) and the
immobilizer control unit.
18. Connect DLC terminals No. 1 and No. 7 to body ground with a jumper wire.
Fig. 141: Connecting DLC Terminals No. 1 And No. 7 To Body Ground With Jumper Wire
Courtesy of AMERICAN HONDA MOTOR CO., INC.
19. Check for continuity between body ground and these connector terminals:
CONNECTOR TERMINAL SPECIFICATION
Connector
Unit Terminal DLC Terminal
2007 Honda Element EX
2007-2008 ENGINE PERFORMANCE PGM-FI System - Element
![](/vehicles/vescileif/qulerpll/din/sane.png)
Is there continuity between the DLC terminal and each of the terminals in the chart?
YES -Replace the unit that does not communicate with the HDS.
NO -Repair open in the wire between the DLC (K-line or DIAG-H line) and the appropriate connector.
20. Do the gauge self-diagnostic function (see SELF-DIAGNOSTIC FUNCTION ).
21. Check odometer/trip meter for "Error 1" message.
Is Error 1 displayed?
YES -Go to step 35.
NO -Go to step 22.
22. Turn the ignition switch OFF.
23. Disconnect the HDS from the DLC.
24. Measure voltage between DLC terminal No. 16 and body ground.
Fig. 142: Measuring Voltage Between DLC Terminal No. 16 And Body Ground
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES -Go to step 25.
NO -Repair open in the wire between DLC terminal No. 16 and the No. 9 BACK UP (10 A) fuse in the
under-hood fuse/relay box.
Gauge control module 36P
No. 9 (LT BLU) No. 7 (LT BLU)
VSA modulator-control unit 47P No. 2 (LT BLU) No. 7 (LT BLU)
SRS unit A 28P
No. 24 (LT BLU) No. 7 (LT BLU)
TPMS control unit B 20P
No. 9 (LT BLU) No. 7 (LT BLU)
Immobilizer control unit 7P
No. 3 (GRY)
No. 1 (GRY)
2007 Honda Element EX
2007-2008 ENGINE PERFORMANCE PGM-FI System - Element
![](/vehicles/vescileif/qulerpll/din/laminaire.png)
25. Measure voltage between DLC terminals No. 4 and No. 16.
Fig. 143: Measuring Voltage Between DLC Terminals No. 4 And No. 16
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES -Go to step 26.
NO -Repair open in the wire between DLC terminal No. 4 and G451.
26. Connect the HDS to the DLC (see GENERAL TROUBLESHOOTING INFORMATION ).
27. Jump the SCS line with the HDS.
28. Disconnect ECM/PCM connector E (31P).
29. Disconnect the HDS from the DLC.
30. Connect DLC terminal No. 6 to body ground with a jumper wire.
Fig. 144: Connecting DLC Terminal No. 6 To Body Ground With Jumper Wire
Courtesy of AMERICAN HONDA MOTOR CO., INC.
31. Check for continuity between ECM/PCM connector terminal E11 and body ground.
2007 Honda Element EX
2007-2008 ENGINE PERFORMANCE PGM-FI System - Element
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст