Honda Odyssey 2004. Manual — part 253
*01
S0X4AA1E10410712251KBAT00
14-406
A/T Gear Position Indicator
Indicator Bulb Replacement
A
B
SRS components are located in this area. Review the
SRS component locations, 2002 model (see page 23-19),
2003-2004 models (see page 23-20), and the
precautions and procedures (see page 23-21) in the SRS
before performing repairs or service.
1. Remove the gauge assembly (see page 22-100).
2. Disassemble the gauge assembly.
3. Replace the bulbs (A) at the gauge assembly (B).
03/07/29 09:45:31 61S0X050_140_0409
*01
S0X4AA1E10436400000DAAT00
14-407
A/T Interlock System
Component Location Index
MULTIPLEX CONTROL
UNIT (DRIVER’S)
SHIFT LOCK SOLENOID
PARK PIN SWITCH
POWERTRAIN CONTROL MODULE (PCM)
BRAKE PEDAL POSITION SWITCH
STEERING LOCK ASSEMBLY
KEY INTERLOCK SOLENOID
KEY INTERLOCK SWITCH
Shift Lock System Circuit
Troubleshooting, page 14-409
Input Test, page 14-414
Shift Lock System Circuit
Troubleshooting, page 14-409
Test, page 14-415
Replacement, page 14-416
Key Interlock System Circuit
Troubleshooting, page 14-412
Test, page 14-417
Key Interlock System Circuit
Troubleshooting, page 14-412
Test, page 14-415
03/07/29 09:45:33 61S0X050_140_0410
*01
S0X4AA1E10436400000EAAT00
−
−
14-408
A/T Interlock System
Circuit Diagram
8
12
16
5
14
11
13
15
22
4
3
1
17
5
1
13
18
24
12
19
16
4
2
14
15
23
11
22
10
21
9
6
7
8
20
3
17
MULTIPLEX CONTROL UNIT, DRIVER’S CONNECTORS
A (24P)
Terminal side of male terminals
B (22P)
Wire side of female terminals
VCC2
YEL/BLU
C28
RED/BLK
C27
TPS
SG2
C18
GRN/YEL
A32
IG1
G401
LG
BLK
B11
A15
A2
A12
YEL
BLK
PG
POWERTRAIN CONTROL MODULE (PCM)
ILU
A28
WHT/RED
BLK/BLU
ATP P
ILU
B12
B22
GRN
2
1
YEL
IG1
BAT
IGNITION SWITCH
No.9 (10A)
UNDER HOOD FUSE/RELAY BOX
No.42 (50A)
No.41 (120A)
No.47 (20A)
BATTERY
WHT/BLK
G401
BLK
WHT/RED
WHT/YEL
WHT/YEL
BK SW
DRIVER’S
UNDER DASH
FUSE/RELAY BOX
STEERING LOCK
ASSEMBLY
KEY
INTERLOCK
SWITCH
KEY
INTERLOCK
SOLENOID
BRAKE
PEDAL
POSITION
SWITCH
SHIFT LOCK
SOLENOID
SHIFT LOCK
SOLENOID
MULTIPLEX CONTROL
UNIT (DRIVER’S)
PARK
PIN
SWITCH
THROTTLE
POSITION
SENSOR
TRANSMISSION
RANGE SWITCH
P POSITION
1
3
3
2
1
P
5
7
03/07/29 09:45:34 61S0X050_140_0411
−
−
−
−
−
−
−
−
02
*01
*02
S0X4AA1E10436455201FAAT10
YES
NO
YES
NO
YES
NO
YES
NO
14-409
Shift Lock System Circuit Troubleshooting
PCM CONNECTOR A (32P)
ILU (WHT/RED)
PCM CONNECTORS
A (32P)
LG2 (BRN/YEL)
LG1 (BRN/YEL)
B (25P)
BK SW (WHT/BLK)
PCM CONNECTORS
LG2 (BRN/YEL)
LG1 (BRN/YEL)
B (25P)
C (31P)
TPS (RED/BLK)
1. Press the brake pedal.
Go to step 2.
Repair faulty brake light circuit.
2. Turn the ignition switch ON (II), and shift to the P
position.
3. Press the brake pedal, and release the accelerator
pedal.
4. Measure the voltage between PCM connector
terminal A28 and body ground.
Check for an open in the wire between PCM
connector terminal A28 and the multiplex control
unit (driver’s). If the wire is OK, check for loose
terminal fit in the multiplex control unit (driver’s)
connectors. If necessary, substitute a known-good
multiplex control unit (driver’s) and recheck.
Go to step 5.
5. Turn the ignition switch OFF, and disconnect the
battery negative terminal.
6. Disconnect PCM connectors A (32P) and B (25P).
7. Press the brake pedal, and measure the voltage
between PCM connector terminals A32 and B20 or
B22.
Release the brake pedal, and go to step 8.
Repair open in the wire between PCM
connector terminal A32 and the brake pedal
position switch.
8. Connect PCM connectors A (32P) and B (25P).
9. Turn the ignition switch ON (II).
10. Measure the voltage between PCM connector
terminals A27 and B20 or B22.
Go to step 18.
Go to step 11.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Ar e the br ake lights ON?
Is ther e batter y voltage?
Is ther e batter y voltage?
Is ther e about 0.5 V ( thr ottle f ully closed)?
03/07/29 09:45:34 61S0X050_140_0412
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст