Honda Odyssey 2004. Manual — part 252
*01
S0X4AA1E10410700000FCAT00
Cavity
Wire Color
Test Condition
Test: Desired Result
Possible Cause
(If result is not obtained)
14-402
A/T Gear Position Indicator
Indicator Input Test
GAUGE ASSEMBLY CONNECTORS
B (22P)
C (16P)
SRS components are located in this area. Review the SRS component locations, 2002 model (see page 23-19), 2003-2004 models (see page 23-
20), and the precautions and procedures (see page 23-21) in the SRS before performing repairs or service.
1. Remove the gauge assembly from the dashboard, then disconnect the gauge assembly B (22P) and C (16P) connectors.
2. Inspect the connectors and connector terminals to be sure they are all making good contact.
• If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the system.
• If the terminals look OK, make the following input tests at the gauge assembly B (22P) and C (16P) connectors.
– If a test indicates a problem, find a correct the cause, then recheck the system.
– If all the input tests prove OK, but the indicator is faulty, replace the printed circuit board.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
B11
YEL
Ignition switch ON (II)
Check for voltage to ground:
There should be battery voltage.
Blown No. 9 (10A) fuse in the driver’s
under-dash fuse/relay box
An open in the wire
B16
BLK
Under all conditions
Check for continuity to ground:
There should be continuity.
Poor ground (G503)
An open in the wire
B22
RED/BLK
Headlights ON
Check for voltage to ground:
There should be battery voltage.
Blown No. 10 (15A) fuse in the
passenger’s under-dash fuse/relay box
An open in the wire
C4
WHT
Ignition switch ON (II)
and shift lever in R
Check for voltage to ground:
There should be 1 V or less.
There should be no battery voltage
in any other shift lever position.
Faulty transmission range switch
An open in the wire
C5
BRN
Ignition switch ON (II)
and shift lever in 1
C6
RED
Ignition switch ON (II)
and shift lever in D3
C7
BLU
Ignition switch ON (II)
and shift lever in 2
C12
GRN/BLK
Ignition switch ON (II)
and shift lever in D
Check for voltage to ground:
There should be battery voltage.
Faulty transmission range switch
Faulty PCM
An open in the wire
C13
YEL
Ignition switch ON (II)
and shift lever in D
Check for voltage to ground:
There should be 1 V or less.
There should be no battery voltage
in any other shift lever position.
Faulty transmission range switch
An open in the wire
C15
BLK/BLU
Shift lever in P
Check for continuity to ground:
There should be no continuity in any
other shift lever position.
Faulty transmission range switch
An open in the wire
C16
RED/BLK
Ignition switch ON (II)
and shift lever in N
Check for voltage to ground:
There should be 1 V or less.
There should be battery voltage in
any other shift lever position.
Wire side of female terminals
03/07/29 09:45:28 61S0X050_140_0405
*01
S0X4AA1E10410759811FEAT00
14-403
Transmission Range Switch Test
B
A
Terminal
Position
1
2
3
4
5
6
7
8
9
10
P
R
D
D3
2
1
Transmission Range Switch Continuity Check
N
1. Remove the transmission range switch connector (A) from the connector bracket (B), then disconnect the
connector.
2. Check for continuity between the terminals in each switch position according to the table.
NOTE: Terminal No.1: Neutral position switch.
03/07/29 09:45:28 61S0X050_140_0406
01
*01
*02
S0X4AA1E10410759811KBAT00
14-404
A/T Gear Position Indicator
Transmission Range Switch Replacement
B
A
C
D
B
A
C
D
1. Raise the vehicle, and make sure it is securely
supported.
2. Shift to the N position.
3. Remove the transmission range switch connector
(A) from the connector bracket (B), then disconnect
the connector.
4. Remove the harness clamp (C) from its bracket (D).
5. Remove the clamp from the clamp bracket on the
transmission housing, and remove the harness
holder (A) from the end cover (B).
6. Remove the transmission range switch cover (C),
then remove the transmission range switch (D)
from the end cover.
7. Set the new transmission range switch to the N
position.
NOTE: The transmission range switch clicks in the
N position.
03/07/29 09:45:29 61S0X050_140_0407
*03
02
03
14-405
E
D
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
A
B
6 x 1.0 mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
C
B
A
C
D
8. Install the transmission range switch (A) on the
control shaft (B), then secure it with the bolts.
NOTE: Do not move the transmission range switch
when tightening the bolts.
9. Install the transmission range switch cover (C), and
the harness holder (D) on the end cover (E).
10. Connect the transmission range switch connector
(A), then install it on the connector bracket (B).
11. Install the harness clamp (C) on its bracket (D).
12. Turn the ignition switch ON (II). Move the shift lever
through all gears, and check the transmission
range switch synchronization with the A/T gear
position indicator.
13. Allow the wheels to rotate freely, then start the
engine.
14. Move the shift lever through all gears, and verify
the following:
• The engine will not start in any position other
than N or P.
• The back-up lights come on when the shift lever
is in the R position.
03/07/29 09:45:31 61S0X050_140_0408
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст