Honda Odyssey 2004. Manual — part 237
![](/vehicles/vescileif/vis/udared/pead.png)
−
−
−
−
−
−
03
*01
*02
YES
NO
YES
NO
YES
NO
14-342
Automatic Transmission
DTC Troubleshooting (cont’d)
LG2 (BRN/YEL)
OP3SW (BLU/WHT)
LG1 (BRN/YEL)
PCM CONNECTORS
B (25P)
D (16P)
BLU/WHT
3RD CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH CONNECTOR
3RD CLUTCH TRANSMISSION FLUID
PRESSURE SWITCH CONNECTOR
7. Raise the front of the vehicle, and make sure it is
securely supported.
8. Set the parking brake, and block the rear wheels
securely.
9. Start the engine, then shift to D3 position and let
the wheels spin in 3rd gear for more than 5
seconds.
10. Measure the voltage between PCM connector
terminals D13 and B20 or B22 .
Check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
Go to step 11.
11. Turn the ignition switch OFF.
12. Disconnect the 3rd clutch transmission fluid
pressure switch connector.
13. Turn the ignition switch ON (II).
14. Measure the voltage between the 3rd clutch
transmission fluid pressure switch connector
terminal and body ground.
Go to step 15.
Repair open in the wire between the 3rd
transmission fluid clutch pressure switch and the
PCM.
15. Measure the resistance between the 3rd clutch
transmission fluid pressure switch connector
terminal and body ground.
Check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
Replace the 3rd clutch transmission fluid
pressure switch (see page 14-365).
Wire side of female terminals
Wire side of female terminal
Terminal side of male terminals
Is ther e about 0 V ?
Is ther e batter y voltage?
Is the r esistance 10 M
and mor e?
03/07/29 09:39:11 61S0X050_140_0345
![](/vehicles/vescileif/vis/udared/qucomeper.png)
−
−
−
−
01
*01
S0X4AA1K77100091705FAAT00
DTC P1705:
YES
NO
YES
NO
14-343
LG2 (BRN/YEL)
ATP R (WHT)
LG1 (BRN/YEL)
PCM CONNECTORS
B (25P)
D (16P)
LG2 (BRN/YEL)
LG1 (BRN/YEL)
ATP NP (BLU/WHT)
PCM CONNECTOR B (25P)
Short in Transmission Range
Switch Circuit
NOTE:
• Record all freeze data and review General
Troubleshooting Information (see page 14-247)
before you troubleshoot.
• This code is caused by an electrical circuit problem
and cannot be caused by a mechanical problem in the
transmission.
1. Turn the ignition switch ON (II).
2. Shift to all positions other than R.
3. Measure the voltage between PCM connector
terminals D6 and B20 or B22 .
Go to step 4.
Check for a short in the wire between PCM
connector terminal D6 and the transmission range
switch or A/T gear position indicator, and check for
an open in the wires between PCM connector
terminals B20 and B22 and body ground (G101). If
the wires are OK, check for loose terminal fit in the
PCM connectors. If necessary, substitute a known-
good PCM and recheck.
4. Shift to all positions other than P or N.
5. Measure the voltage between PCM connector
terminals B14 and B20 or B22 .
Go to step 6.
Check for a short in the wire between PCM
connector terminal B14 terminal and the
transmission range switch. If the wires are OK,
check for loose terminal fit in the PCM connectors.
If necessary, substitute a known-good PCM and
recheck.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is ther e about 5 V ?
03/07/29 09:39:12 61S0X050_140_0346
![](/vehicles/vescileif/vis/udared/zersorte.png)
−
−
−
−
02
03
YES
NO
YES
NO
14-344
Automatic Transmission
DTC Troubleshooting (cont’d)
LG2 (BRN/YEL)
ATP D5 (YEL)
LG1 (BRN/YEL)
PCM CONNECTORS
B (25P)
D (16P)
LG2 (BRN/YEL)
ATP D3 (RED)
LG1 (BRN/YEL)
PCM CONNECTORS
B (25P)
D (16P)
6. Shift to all positions other than D.
7. Measure the voltage between PCM connector
terminals D9 and B20 or B22 .
Go to step 8.
Check for a short in the wire between PCM
connector terminal D9 and the transmission range
switch or A/T gear position indicator. If the wire is
OK, check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
8. Shift to all positions other than D3.
9. Measure the voltage between PCM connector
terminals D8 and B20 or B22.
Go to step 10.
Check for a short in the wire between PCM
connector terminal D8 and the transmission range
switch or A/T gear position indicator. If the wires
are OK, check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
Wire side of female terminals
Wire side of female terminals
Is ther e about 5 V ?
Is ther e batter y voltage?
03/07/29 09:39:12 61S0X050_140_0347
![](/vehicles/vescileif/vis/udared/fisw.png)
−
−
−
−
04
05
YES
NO
YES
NO
14-345
LG2 (BRN/YEL)
ATP 2 (BLU)
LG1 (BRN/YEL)
PCM CONNECTORS
B (25P)
D (16P)
LG2 (BRN/YEL)
ATP 1 (BRN)
LG1 (BRN/YEL)
PCM CONNECTORS
B (25P)
D (16P)
10. Shift to all positions other than 2.
11. Measure the voltage between PCM connector
terminals D14 and B20 or B22 .
Go to step 12.
Check for a short in the wire between PCM
connector terminal D14 and the transmission range
switch or A/T gear position indicator. If the wires
are OK, check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
12. Shift to all positions other than 1.
13. Measure the voltage between PCM connector
terminals D15 and B20 or B22.
Check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
Check for a short in the wire between PCM
connector terminal D15 and the transmission range
switch or A/T gear position indicator. If the wires
are OK, check for loose terminal fit in the PCM
connectors. If necessary, substitute a known-good
PCM and recheck.
Wire side of female terminals
Wire side of female terminals
Is ther e batter y voltage?
Is ther e batter y voltage?
03/07/29 09:39:13 61S0X050_140_0348
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст