Honda Odyssey 2004. Manual — part 585
S0X4AZBK791000RD111FAAT10
’03-04 Models
DTC D1-11, D2-11, D3-11, D4-11, D7-11,
E2-11, E4-11, F1-11 F2-11, F3-11, F4-11:
23-282
SRS
DTC Troubleshooting (cont’d)
Airbags, Side airbags, and/or Seat Belt
Tensioners Deployed.
The SRS unit must be replaced after any airbags and/or
tensioners have deployed (see page 23-384).
03/07/29 10:39:46 61S0X050_230_0282
−
−
−
−
−
01
02
S0X4AZBK791000R611XFAAT20
’03-04 Models
DTC 61-1x (61-10 to 61-19, 61-1A to 61-1F):
YES
NO
YES
NO
23-283
A
DRIVER’S SEAT BELT BUCKLE SWITCH
3P CONNECTOR
BLU
BLK
BLK
GRY
Open in Driver’s Seat Belt Buckle Switch
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), then buckle and
unbuckle the driver’s seat belt several times.
3. Read the DTC (see page 23-38).
Go to step 4.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
4. Turn the ignition switch OFF.
5. Disconnect the driver’s seat belt buckle switch 3P
connector (A).
6. Buckle the driver’s seat belt.
• Check resistance between the No. 1 and No. 3
terminals of the driver’s seat belt buckle switch
3P connector. There should be 0
1
.
• Check resistance between the No. 1 and No. 2
terminals of the same connector. There should
be an open circuit, or at least 1 M
.
Go to step 7.
Replace the driver’s seat belt buckle assembly,
then clear the DTC.
(cont’d)
Terminal side of male terminals
Terminal side of male terminals
Is DT C 61-1x indicated?
Ar e the r esistance r eadings as specif ied?
03/07/29 10:39:46 61S0X050_230_0283
−
−
−
−
−
−
*01
*02
05
YES
NO
YES
NO
23-284
SRS
DTC Troubleshooting (cont’d)
BLK
BLU
BLK
GRY
DRIVER’S SEAT BELT BUCKLE SWITCH
3P CONNECTOR
DRIVER’S SEAT WIRE HARNESS 3P CONNECTOR
(WITH POWER SEAT)
LEFT SIDE WIRE HARNESS 3P CONNECTOR
(WITHOUT POWER SEAT)
BLK
A
7. Unbuckle the driver’s seat belt.
• Check resistance between the No. 1 and No. 2
terminals of the driver’s seat belt buckle switch
3P connector. There should be 0
1
.
• Check resistance between the No. 1 and No. 3
terminals of the same connector. There should
be an open circuit, or at least 1 M
.
Go to step 8.
Replace the driver’s seat belt buckle assembly,
then clear the DTC.
8. Check resistance between the No. 1 terminal of the
driver’s seat wire harness (with power seat) or left
side wire harness (without power seat) 3P
connector and body ground. There should be
0
1
.
Go to step 9.
Open in the driver’s seat wire harness (with
power seat), left side wire harness (without power
seat) or poor ground connection at G551. If G551 is
OK, replace the faulty harness.
9. Disconnect the battery negative cable and wait for
3 minutes.
10. Disconnect both seat belt tensioner 2P connectors
(A).
Terminal side of male terminals
Terminal side of male terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:39:47 61S0X050_230_0284
−
−
−
−
−
−
06
*03
*04
YES
NO
YES
NO
23-285
B
SRS UNIT
CONNECTOR B (28P)
DRIVER’S SEAT WIRE HARNESS
3P CONNECTOR (WITH POWER SEAT)
LEFT SIDE WIRE HARNESS
3P CONNECTOR
(WITHOUT POWER SEAT)
BLU/RED
BLU/RED
SRS UNIT
CONNECTOR B (28P)
DRIVER’S SEAT WIRE HARNESS
3P CONNECTOR (WITH POWER SEAT)
LEFT SIDE WIRE HARNESS
3P CONNECTOR
(WITHOUT POWER SEAT)
RED/BLU
RED/BLU
11. Disconnect SRS unit connector B (28P) from the
SRS unit.
12. Check resistance between the No. 17 terminal of
SRS unit connector B (28P) and the No. 3 terminal
of the driver’s seat wire harness (with power seat)
or left side wire harness (without power seat) 3P
connector. There should be 0
1
.
Go to step 13.
Open in the driver’s seat wire harness (with
power seat), left side wire harness, dashboard wire
harness A, SRS main harness or SRS floor harness;
replace the faulty harness.
13. Check resistance between the No. 11 terminal of
SRS unit connector B (28P) and the No. 2 terminal
of the driver’s seat wire harness (with power seat)
or left side wire harness (without power seat) 3P
connector. There should be 0
1
.
Replace the SRS unit (see page 23-384).
Open in the driver’s seat wire harness (with
power seat), left side wire harness, dashboard wire
harness A, SRS main harness or SRS floor harness
or multiplex control unit, or poor connection at the
left side wire harness, the driver’s under-dash fuse/
relay box, and the multiplex control unit. Check the
connection at the left side wire harness, the driver’s
under-dash fuse/relay box, and the multiplex
control unit. If the connection is OK, replace the
faulty harness or part.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:39:48 61S0X050_230_0285
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст