Honda Odyssey 2004. Manual — part 534
−
−
−
−
02
02
04
YES
NO
YES
NO
23-78
SRS
DTC Troubleshooting (cont’d)
B
A
A
SRS MAIN HARNESS 18P CONNECTOR
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short in the front passenger’s airbag inflator;
replace the front passenger’s airbag (see page 23-
370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 2P connector (A) and
both seat belt tensioner 2P connectors (B).
11. Disconnect the special tool (2
) from the SRS main
harness 2P connector.
12. Disconnect the SRS main harness 18P connector
(A) from the SRS unit.
13. Check resistance between the No. 10 and No. 14
terminals of the SRS main harness 18P connector.
There should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Short to another wire in the SRS main
harness; replace the SRS main harness.
Wire side of female terminals
Is DT C 2-3 indicated?
Is the r esistance as specif ied?
03/07/29 10:33:02 61S0X050_230_0078
−
−
−
−
01
02
S0X4AZ4K79100081024FAAT00
’99-01 Models
DTC 2-4:
YES
NO
YES
NO
23-79
07TAZ-SZ5011A
07SAZ-TB4011A
A
B
A
Short to Power in Front Passenger’s
Airbag Inflator
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s airbag 2P
connector from the SRS main harness 2P connector
(A).
5. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the front passenger’s airbag
inflator; replace the front passenger’s airbag (see
page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 2P connector (A) and
both seat belt tensioner 2P connectors (B), and
disconnect the special tool from the SRS main
harness 2P connector.
(cont’d)
Does the SRS indicator stay on?
Is DT C 2-4 indicated?
03/07/29 10:33:02 61S0X050_230_0079
−
−
−
−
02
04
01
S0X4AZ4K79100081025FAAT00
YES
NO
YES
NO
’99-01 Models
DTC 2-5:
23-80
23-80
SRS
DTC Troubleshooting (cont’d)
A
SRS MAIN HARNESS 18P CONNECTOR
07TAZ-SZ5011A
07SAZ-TB4011A
A
11. Disconnect the SRS main harness 18P connector
(A) from the SRS unit.
12. Reconnect the battery negative cable.
13. Turn the ignition switch ON (II).
14. Check for voltage between the No. 10 terminal of
the SRS main harness 18P connector and body
ground, and between the No. 14 terminal and body
ground. There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Short to power in the SRS main harness;
replace the SRS main harness.
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Disconnect the battery negative cable, and wait for
3 minutes.
4. Disconnect the front passenger’s airbag 2P
connector from the SRS main harness 2P connector
(A).
5. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
Short to Ground in Front Passenger’s
Airbag Inflator
Wire side of female terminals
Is the voltage as specif ied?
Does the SRS indicator stay on?
03/07/29 10:33:03 61S0X050_230_0080
−
−
−
−
02
01
04
YES
NO
YES
NO
23-81
B
A
A
SRS MAIN HARNESS 18P CONNECTOR
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to ground in the front passenger’s
airbag inflator; replace the front passenger’s airbag
(see page 23-370).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s airbag 2P connector (A) and
both seat belt tensioner 2P connectors (B), and
disconnect the special tool from the SRS main
harness 2P connector.
11. Disconnect the SRS main harness 18P connector
(A) from the SRS unit.
12. Check resistance between the No. 10 terminal of
the SRS main harness 18P connector and body
ground, and between the No. 14 terminal and body
ground. There should be an open circuit, or at least
1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Short to ground in the SRS main harness;
replace the SRS main harness.
Wire side of female terminals
Is DT C 2-5 indicated?
Is the r esistance as specif ied?
03/07/29 10:33:04 61S0X050_230_0081
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст