Honda Odyssey 2004. Manual — part 373
02
01
S0X4AZAJ18533231701KBAT00
’02-04 models
20-134
20-134
Hood
Adjustment (cont’d)
Hood Insulator Replacement
Forward
Fastener Locations
: Clip, 10
A
B
4. Tighten each bolt securely.
5. Check that the hood opens properly and locks
securely.
6. Apply touch-up paint to the hinge mounting bolts
and around the hinges.
7. Remove the front bulkhead cover (see page 20-142),
and Apply multipurpose grease to the hood latch
and hood hinge as indicated by the arrows.
1. Using a clip remover, detach the clips, then release
the hood insulator (A) from the hooks (B). Take care
not to bend the insulator and not to scratch the
hood.
2. Install the insulator in the reverse order of removal,
and note thses items:
• Replace any damaged clips.
• Push the clips into place securely.
03/07/29 10:03:35 61S0X050_200_0136
01
S0X4A00J18533232201KBAT00
20-135
Hood Seal and Hood Molding Replacement
Fastener Locations
A
: Clip, 20
E
: Clip, 18
B
: Clip, 6
F
E
C
A
B
D
1. Using a clip remover, detach the clips (A, B), then
remove the hood seal (C) and hood sub-seal (D). On
Canadian models, detach the clips (E), then remove
the hood molding (F). Take care not to scratch the
hood.
2. Install the seal and molding in the reverse order of
removal, and note these items:
• Replace any damaged clips.
• Push the clips into place securely.
03/07/29 10:03:35 61S0X050_200_0137
01
S0X4A00J18573900000KBAT00
20-136
Tailgate
Replacement
Fastener Locations
: Harness clip
A
F
C
D
E
B
NOTE: Put on gloves to protect your hands.
1. Remove the tailgate trim panel (see page 20-61).
2. Remove the tailgate spoiler (see page 20-140).
3. Disconnect the tailgate harness connectors (A), and rear window defogger connector (B). Detach the harness clips
(C), and remove the grommets (D), then remove the wire harness (E) from the tailgate (F).
03/07/29 10:03:35 61S0X050_200_0138
*01
03
20-137
Fastener Locations
: Bolt, 4
8 x 1.25 mm
29 N·m
(3.0 kgf·m,
22 lbf·ft)
E
B
C
A
C
C
D
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
C
B
A
4. With a flat-tip screwdriver (A), pry the support strut clips (B) away from each of the support struts (C), but do not
remove the clips. With the help of an assistant, release the support struts from the pivot bolts (D).
5. With the help of an assistant, remove the bolts, then remove the tailgate (E). Take care not to damage the tailgate
and body.
6. Install the tailgate in the reverse order of removal, and note these items:
•
• Make sure the tailgate opens properly and locks securely.
• Make sure the connectors are connected properly, and the wire harness is routed properly.
• When reattaching the support struts (A), set the clips (B) to their original position, then push the support struts
onto the pivot bolts (C).
03/07/29 10:03:36 61S0X050_200_0139
Before reattaching the support struts, adjust the tailgate alignment (see page 20-138).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст