Honda Odyssey 2004. Manual — part 374
01
S0X4A00J18573900000MBAT00
20-138
Tailgate
Adjustment
A
C
B
D
D
8 x 1.25 mm
18 N·m
(1.8 kgf·m, 13 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
1. Remove the support strut from each side (see page 20-139).
2. Slightly loosen each bolt and nut.
3. Adjust the tailgate alignment in the following sequence:
• Pull down the rear portion of the headliner (see page 20-62). Take care not to bend the headliner excessively.
Adjust the tailgate hinges (A) right and left, as well as forward and rearward, using the elongated holes.
• Turn the tailgate edge cushions (B), in or out as necessary, to make the tailgate (C), fit flush with the body at the
side edges.
• Adjust the fit between the tailgate and tailgate opening by moving the striker (D).
4. Tighten each bolt and nut securely.
03/07/29 10:03:36 61S0X050_200_0140
02
01
02
S0X4A00J18573958551KBAT00
20-139
20-139
Tailgate Support Strut
Replacement
A
D
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
B
C
A
C
C
A
B
5. Check that the tailgate opens properly and locks
securely.
6. Reinstall the support struts securely.
7. Apply touch-up paint to the hinge mounting nuts
and around the hinges.
8. Apply multipurpose grease to the pivot portion of
the tailgate hinges (A) as indicated by the arrows.
1. With the help of an assistant, use a flat-tip
screwdriver (A) to pry the support strut clips (B)
from each end of the support strut (C) at the tailgate
and body, then release the support strut from the
pivot bolts (D). Do not remove the clips from the
support strut.
2. Set the clips (A) to their original position, then
reattach the support struts (B) by pushing them
onto the pivot bolts (C).
03/07/29 10:03:37 61S0X050_200_0141
01
02
03
S0X4A00J18573958451KBAT00
20-140
Tailgate
Tailgate Spoiler Replacement
Fastener Locations
: Nut, 4
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
C
B
A
A
C
B
1. Remove the nuts from the tailgate spoiler.
2. Disconnect the rear window washer tube (A).
Remove the access cap (B) from the tailgate, and
detach the clip (C).
3. Gently close the tailgate, and lift up on the tailgate
spoiler (A). Remove the high mount brake light
connector grommet (B) from the tailgate, and
disconnect the high mount brake light connector
(C), then remove the tailgate spoiler. Take care not
to scratch the tailgate and body.
4. Install the spoiler in the reverse order of removal,
and make sure the connector is plugged in properly
and the washer tube is connected properly.
03/07/29 10:03:38 61S0X050_200_0142
01
S0X4A00J18573958801KBAT00
Sealant: Cemedine P/N 08712-0004, or equivalent
20-141
Tailgate Weatherstrip Replacement
A
A
B
C
Inside
1. Remove the tailgate weatherstrip (A) by pulling out
on it.
2. Apply clear sealant (B) into the channel of the
tailgate weatherstrip all the way around.
3. Locate the painted alignment mark (C) on the
tailgate weatherstrip. Align the painted mark with
the alignment tab in the the center of the tailgate
opening, and install the tailgate weatherstrip all the
way around in the direction shown. Make sure
there are no wrinkles in the weatherstrip.
4. Check for water leaks.
03/07/29 10:03:38 61S0X050_200_0143
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст