Honda Odyssey 2004. Manual — part 353
13
20-54
Glass
Sliding Door Glass Replacement (cont’d)
A
18. Use suction cups (A) to hold the sliding door glass
over the opening, align it and set it down on the
adhesive. Lightly push on the sliding door glass
until its edges are fully seated on the adhesive all
the way around. Do not open or close the doors
until the adhesive is dry.
19. Scrape or wipe the excess adhesive off with a putty
knife or towel. To remove adhesive from a painted
surface or the rear window, use a soft shop towel
dampened with alcohol.
20. Let the adhesive dry for at least 1 hour, then spray
water over the sliding door glass and check for
leaks. Mark any leaking areas, let the sliding door
glass dry, then seal with sealant. Let the vehicle
stand for at least 4 hours after sliding door glass
installation. If the vehicle has to be used within the
first 4 hours, it must be driven slowly.
21. Reinstall all remaining removed parts.
NOTE: Advise the customer not to do the following
things for 2 to 3 days:
• Slam the doors with all the windows rolled up.
• Twist the body excessively (such as when going
in and out of driveways at an angle or driving
over rough, uneven roads).
03/07/29 10:01:36 61S0X050_200_0056
01
S0X4A00J54400048101KBAT20
20-55
Quarter Glass and Regulator Replacement
Fastener Locations
A
: Screw, 2
5 x 0.8 mm
4 N·m
(0.4 kgf·m,
3 lbf·ft)
B
Bolt, 4 (Power)
Bolt, 2 (Manual)
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
QUARTER GLASS OPENER
GLASS SEAL
QUARTER GLASS
OPENER CONNECTOR
QUARTER GLASS
QUARTER GLASS HINGE BASE
A
A
QUARTER SEAL
QUARTER
GLASS
14 mm
(0.51 in.)
CAP
SCREW
SEAL
ATTACHMENT PIN
QUARTER GLASS
ATTACHMENT
LOWER END CAP
E-CLIP
LOCK PIN
SEAL
GLASS LOCK
B
QUARTER GLASS LOCK
NOTE:
• When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related
parts, to prevent damage.
• Put on gloves to protect your hands.
1. Remove the quarter glass and the quarter glass opener or the quarter glass lock as shown.
2. Install the quarter glass and the opener or the lock in the reverse order of the removal, and note these items:
• If necessary, replace the quarter glass seal.
• The glass and body edges should be parallel.
• Make sure the glass locks properly. If necessary adjust the quarter glass opener or quarter glass lock mount
position.
• Check for water leaks.
Remove the rear pillar trim.
Remove the rear pillar trim.
03/07/29 10:01:37 61S0X050_200_0057
01
02
03
S0X4A00J54400048071KBAT00
20-56
Glass
Quarter Glass Hinge Base Replacement
A
B
A
A
1. Remove the plate (A), and turn the nut (B) as shown.
2. Pull out the quarter glass hinge base (A).
3. Install the quarter glass hinge base on the body,
then set the quarter glass and install the screw (A).
03/07/29 10:01:38 61S0X050_200_0058
*01
S0X4A00J26273400000DAAT00
20-57
Interior Trim
Component Location Index
SLIDING DOOR OPENING TRIM
CENTER PILLAR UPPER TRIM
REAR TRIM PANEL
REAR SIDE TRIM PANEL
CENTER PILLAR LOWER TRIM PANEL
SLIDING DOOR SILL TRIM
FRONT DOOR SILL TRIM
FRONT PILLAR TRIM
FRONT DOOR OPENING TRIM
HEADLINER
REAR CARPET
TAILGATE SIDE TRIM
TAILGATE UPPER TRIM
TAILGATE TRIM PANEL
KICK PANEL
FRONT CARPET
QUARTER PILLAR TRIM
QUARTER GLASS OPENING TRIM
REAR PILLAR TRIM
page 20-58
page 20-58
page 20-60
page 20-60
page 20-58
page 20-58
page 20-58
page 20-58
page 20-58
Removal/Installation, page 20-62
Replacement, page 20-65
page 20-61
page 20-61
page 20-61
page 20-58
Replacement, page 20-65
page 20-59
page 20-59
page 20-59
03/07/29 10:01:42 61S0X050_200_0059
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст