Honda Odyssey 2004. Manual — part 362
*01
S0X4AZBJ46127053901MFAT00
’03-04 models
20-90
Seats
Front Seat Disassembly/Reassembly - Manual Height Adjustable (cont’d)
INNER SEAT TRACK
CONNECTING WIRE
RECLINE ADJUSTER/
OUTER SEAT TRACK
END CAP
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
RECLINE
COVER
RECLINE
LEVER
WASHER
WASHER
90°
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
HEIGHT
KNOB
SEAT RISER
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
PIVOT WASHER
HOOKS
BUSHING
HEADREST
SEAT-BACK
SEAT CUSHION
CENTER COVER
WIRE TIE
CLIP
SIDE AIRBAG HARNESS
(For some models)
HOOK
HOOKS
END CAP
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
SEAT POSITION
SENSOR
SEAT POSITION
SENSOR
SUBHARNESS
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
CLIP
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
WASHER
10 x 1.25 mm
47 N·m
(4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
WASHER
CENTER COVER
• For some models: SRS components are located in this area. Review the SRS component locations (see page 23-20),
and the precautions and procedures (see page 23-21) before performing repairs or service.
• The operation of the driver’s seat position sensor must be checked after any of these actions (see page 23-47):
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail) replacement
NOTE:
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
Twist 90° to connect.
Use a Torx T30 bit.
03/07/29 10:02:12 61S0X050_200_0092
*01
S0X4AC4J46127053901MFAT10
’99-02 models Without Side Airbag
20-91
Front Seat Disassembly/Reassembly - Manual
HOOK
HEADREST
SEAT-BACK
SEAT CUSHION
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
RECLINE COVER
RECLINE LEVER
RECLINE ADJUSTER/
OUTER SEAT TRACK
SEAT RISER
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
PIVOT
WASHER
10 x 1.25 mm
47 N·m
(4.8 kgf·m, 35 lbf·ft)
BUSHING
INNER SEAT
TRACK
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
UPPER END CAP
CENTER COVER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
90°
LOWER END CAP
CONNECTING WIRE
CONNECTING
WIRE
UPPER END CAP
LOWER END CAP
NOTE:
• The passenger’s seat is shown, the driver’s seat is similar except that it has a seat belt switch harness and doesn’t
have a center table, under seat storage tray, and navigation unit (for some models).
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
Twist 90° to connect.
03/07/29 10:02:13 61S0X050_200_0093
*01
S0X4AC5J46127053901MFAT00
’02 model With Side Airbag
20-92
Seats
Front Seat Disassembly/Reassembly - Manual (cont’d)
HOOK
HEADREST
SEAT-BACK
SEAT CUSHION
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
COVER
RECLINE LEVER
RECLINE ADJUSTER/
OUTER SEAT TRACK
SEAT RISER
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
PIVOT
WASHER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
BUSHING
INNER SEAT
TRACK
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
UPPER END CAP
CENTER COVER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
90°
LOWER END CAP
CONNECTING WIRE
CONNECTING
WIRE
UPPER END CAP
LOWER END CAP
OPDS UNIT HARNESS
SEAT BELT
SWITCH HARNESS
SIDE AIRBAG
HARNESS
PASSENGER’S SEAT
SUBHARNESS
(With under seat storage tray)
HOOKS
WIRE TIE
SRS components are located in this area. Review the SRS component locations (see page 23-19), and the precautions
and procedures (see page 23-21) before performing repairs or service.
NOTE:
• The passenger’s seat with under seat storage tray is shown, the driver’s seat is similar except that it doesn’t have
the OPDS unit, center table, under seat storage tray, and navigation unit (for some models), and the passenger’s
seat without under seat storage tray has no passenger subharness (see page 20-94).
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
Twist 90° to connect.
03/07/29 10:02:14 61S0X050_200_0094
*01
S0X4AZ9J46127053901MFAT00
’03-04 models
20-93
HOOK
HEADREST
SEAT-BACK
SEAT CUSHION
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m
(4.8 kgf·m, 35 lbf·ft)
COVER
RECLINE LEVER
RECLINE ADJUSTER/
OUTER SEAT TRACK
SEAT RISER
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
PIVOT
WASHER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
BUSHING
INNER SEAT
TRACK
UPPER END CAP
CENTER COVER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
90°
LOWER END CAP
CONNECTING WIRE
CONNECTING
WIRE
UPPER END CAP
LOWER END CAP
OPDS UNIT HARNESS
(For some models)
SEAT BELT
SWITCH HARNESS
SIDE AIRBAG
HARNESS
(For some models)
PASSENGER’S SEAT
SUBHARNESS
(With under seat storage tray)
HOOKS
SEAT CUSHION HEATER HARNESS
(For some models)
OUTER
WEIGHT
SENSOR
INNER WEIGHT SENSOR
HARNESS BRACKET COVER
CLIPS
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
WIRE TIE
• SRS components are located in this area. Review the SRS component locations (see page 23-20), and the
precautions and procedures (see page 23-21) before performing repairs or service.
• The front passenger’s weight sensor (SWS) unit must be calibrated after any of these actions (see page 23-42):
– Front passenger’s seat replacement (including any seat components)
– Replacement of the seat weight sensors
– Replacement of the seat weight sensor unit
NOTE:
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
Twist 90° to connect.
03/07/29 10:02:15 61S0X050_200_0095
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст