Honda Odyssey 2004. Manual — part 361
*01
S0X4AZ4J46127053901MFAT00
’99-01 models Without Side Airbag
20-86
Seats
Front Seat Disassembly/Reassembly - 8-Way Power
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
HOOK
HEADREST
SEAT-BACK
SEAT CUSHION
FRONT COVER
HEIGHT INNER COVER
CENTER COVER
CLIP
(To seat cushion
cover)
SEAT LINKAGE
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
POWER
SEAT
SWITCH
SEAT CUSHION COVER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
RECLINE
COVER
CLIP
(To seat cushion
cover)
SWITCH
KNOBS
HEIGHT OUTER COVER
PIVOT WASHER
BUSHING
NOTE:
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
03/07/29 10:02:08 61S0X050_200_0088
*01
S0X4AZAJ46127053901MFAT00
’02-04 models With Side Airbag
20-87
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
PIVOT WASHER
HOOKS
CENTER COVER
BUSHING
HEADREST
SEAT CUSHION COVER
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
RECLINE COVER
SEAT-BACK
SEAT CUSHION
FRONT COVER
WIRE TIE
HOOK
SEAT-BACK
HEATER HARNESS
(For some models)
SEAT CUSHION HEATER HARNESS
(For some models)
CLIP
(To seat cushion
cover)
SWITCH
KNOBS
HEIGHT OUTER COVER
POWER
SEAT
SWITCH
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
SEAT LINKAGE
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
CLIP
(To seat cushion
cover)
SIDE AIRBAG HARNESS
HOOK
HOOK
HEIGHT INNER COVER
• SRS components are located in this area. Review the SRS component locations, ’02 model (see page 23-19), ’03-04
models (see page 23-20), and the precautions and procedures (see page 23-21) before performing repairs or service.
• For ’03-04 models: The operation of the driver’s seat position sensor must be checked after any of these actions (see
page 23-47):
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail) replacement
NOTE:
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
• Replace the back panel clips with new ones.
03/07/29 10:02:09 61S0X050_200_0089
*01
S0X4AZ1J46127053901MFAT00
’01 model Without Side Airbag
20-88
Seats
Front Seat Disassembly/Reassembly - Manual Height Adjustable
CENTER COVER
HEADREST
HOOK
SEAT-BACK
HOOK
PIVOT WASHER
PIVOT NUT
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
WASHER
CONNECTING
WIRE
BUSHING
END CAP
RECLINE ADJUSTER/
OUTER SEAT TRACK
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
RECLINE COVER
HEIGHT
KNOB
RECLINE
LEVER
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
SEAT RISER
WASHER
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
WASHER
END CAP
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
CLIP
90°
INNER SEAT TRACK
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
SEAT CUSHION
WASHER
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
NOTE:
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
Twist 90° to
connect.
03/07/29 10:02:10 61S0X050_200_0090
*01
S0X4AZ3J46127053901MFAT00
’02 model With Side Airbag
20-89
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
INNER SEAT TRACK
CONNECTING WIRE
WASHER
RECLINE ADJUSTER/
OUTER SEAT TRACK
END CAP
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
RECLINE COVER
RECLINE
LEVER
WASHER
WASHER
90°
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
10 x 1.25 mm
47 N·m (4.8 kgf·m,
35 lbf·ft)
HEIGHT
KNOB
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
SEAT RISER
PIVOT NUT
8 x 1.25 mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
PIVOT WASHER
HOOKS
BUSHING
HEADREST
SEAT-BACK
SEAT CUSHION
CENTER COVER
WIRE TIE
CLIP
SIDE AIRBAG HARNESS
HOOK
HOOKS
END CAP
10 x 1.25 mm
47 N·m (4.8 kgf·m, 35 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
WASHER
SRS components are located in this area. Review the SRS component locations (see page 23-19), and the precautions
and procedures (see page 23-21) before performing repairs or service.
NOTE:
• Route the seat wire harness correctly (see page 20-94).
• Make sure the bushing and pivot washer are installed correctly.
• Apply multipurpose grease to the moving portion of the seat track.
• To prevent wrinkles in the seat-back cover, stretch the material evenly over the pad.
Twist 90° to connect.
03/07/29 10:02:11 61S0X050_200_0091
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст