Honda Odyssey 2004. Manual — part 553
−
−
−
−
−
−
*05
13
*06
15
YES
NO
YES
NO
23-154
SRS
DTC Troubleshooting (cont’d)
A
C503
SRS UNIT CONNECTOR C (8P)
YEL/BLU
YEL/BLU
SRS MAIN HARNESS
8P CONNECTOR
A
C503
SRS UNIT CONNECTOR C (8P)
BLU
BLU
SRS MAIN HARNESS
8P CONNECTOR
19. Disconnect the SRS main harness 8P connector (A)
from the dashboard wire harness 8P connector
C503.
20. Check resistance between the No. 7 terminal of
SRS unit connector C (8P) and the No. 2 terminal of
the SRS main harness 8P connector. There should
be 0
1
.
Open in the right side wire harness or
dashboard wire harness; replace the faulty
harness.
Open in the SRS main harness or SRS floor
harness; replace the SRS floor harness.
21. Disconnect the SRS main harness 8P connector (A)
from the dashboard wire harness 8P connector
C503.
22. Check resistance between the No. 3 terminal of
SRS unit connector C (8P) and the No. 3 terminal of
the SRS main harness 8P connector. There should
be 0
1
.
Open in the right side wire harness or
dashboard wire harness; replace the faulty
harness.
Open in the SRS main harness or SRS floor
harness; replace the SRS floor harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:04 61S0X050_230_0154
−
−
−
−
01
02
03
S0X4AZ3K79100081096FAAT00
’02 Model
DTC 9-6:
Special Tools Required
YES
NO
YES
NO
23-155
A
A
A
Faulty Left Front Sensor
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead H 07YAZ-S3AA100
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Check the
connections between SRS unit connector A (18P)
and the SRS unit, and between the left engine
compartment wire harness 2P connector and the
left front sensor (see page 23-19), and at the 4P
connector between the SRS main harness and the
SRS floor harness.
Go to step 4.
Repair the poor connections and retest. If DTC
9-6 is still present, go to step 4.
4. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
5. Disconnect the driver’s airbag 4P connector from
the cable reel 4P connector (A).
6. Disconnect the front passenger’s airbag 4P
connector from the SRS main harness 4P connector
(A).
7. Disconnect both seat belt tensioner 2P connectors
from the side wire harness 2P connectors (A).
(cont’d)
Does the SRS indicator stay on?
Ar e the connections OK ?
03/07/29 10:36:04 61S0X050_230_0155
−
−
−
−
04
05
06
07
YES
NO
YES
NO
23-156
SRS
DTC Troubleshooting (cont’d)
A
A
SRS UNIT CONNECTOR A (18P)
SRS UNIT CONNECTOR A (18P)
8. Disconnect the left engine compartment wire
harness 2P connector (A) from the left front sensor.
9. Disconnect SRS unit connector A (18P) from the
SRS unit.
10. Check resistance between the No. 10 and No. 11
terminals of SRS unit connector A (18P). There
should be an open circuit, or at least 1 M
.
Go to step 11.
Go to step 17.
11. Reconnect the battery negative cable.
12. Turn the ignition switch ON (II).
13. Check for voltage between the No. 10 terminal of
SRS unit connector A (18P) and body ground. There
should be 1 V or less.
Go to step 14.
Go to step 19.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the voltage as specif ied?
03/07/29 10:36:05 61S0X050_230_0156
−
−
−
−
08
09
*01
11
YES
NO
YES
NO
23-157
A
07YAZ-S3AA100
07SAZ-TB4011A
SRS UNIT CONNECTOR A (18P)
C851
A
SRS MAIN HARNESS 28P CONNECTOR
14. Turn the ignition switch OFF.
15. Connect the special tool (jumper connector) to the
left engine compartment wire harness 2P
connector (A).
16. Check resistance between the No. 10 and No. 11
terminals of SRS unit connector A (18P). There
should be 1
or less.
Faulty left front sensor or SRS unit. Replace
the left front sensor; if the problem is still present,
replace the SRS unit (see page 23-382).
Go to step 23.
17. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
18. Check resistance between the No. 12 and No. 27
terminals of the SRS main harness 28P connector.
There should be an open circuit, or at least 1 M
.
Short in the SRS floor harness; replace the
SRS floor harness.
Short in the left engine compartment wire
harness or SRS main harness; replace the faulty
harness.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:06 61S0X050_230_0157
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст