Honda Odyssey 2004. Manual — part 552
−
−
−
−
−
01
*01
S0X4AZ3K79100081094FAAT00
’02 Model
DTC 9-4:
YES
NO
YES
NO
23-150
SRS
DTC Troubleshooting (cont’d)
A
B
FRONT PASSENGER’S SEAT BELT
BUCKLE SWITCH 3P CONNECTOR
BLK
BLU/RED
BLK
RED/BLU
Faulty Front Passenger’s Seat Belt
Buckle Switch
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), then buckle and
unbuckle the front passenger’s seat belt several
times.
3. Read the DTC (see page 23-35).
Go to step 4.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
4. Turn the ignition switch OFF.
5. Disconnect the front passenger’s seat belt buckle
switch 3P connector (A) from the floor wire harness
3P connector (B).
6. Buckle the front passenger’s seat belt.
• Check resistance between the No. 1 and No. 3
terminals of the front passenger’s seat belt
buckle switch 3P connector. There should be
0
1
.
• Check resistance between the No. 1 and No. 2
terminals of the same connector. There should
be an open circuit, or at least 1 M
.
Go to step 7.
Replace the front passenger’s seat belt buckle
assembly, and clear the DTC.
Terminal side of male terminals
Terminal side of male terminals
Is DT C 9-4 indicated?
Is the r esistance as specif ied?
03/07/29 10:34:58 61S0X050_230_0150
−
−
−
−
−
−
*02
02
03
YES
NO
YES
NO
23-151
BLK
BLU/RED
BLK
RED/BLU
FRONT PASSENGER’S SEAT BELT
BUCKLE SWITCH 3P CONNECTOR
RIGHT SIDE WIRE HARNESS 3P CONNECTOR
BLK
C
7. Unbuckle the front passenger’s seat belt.
• Check resistance between the No. 1 and No. 2
terminals of the front passenger’s seat belt
buckle switch 3P connector. There should be
0
1
.
• Check resistance between the No. 1 and No. 3
terminals of the same connector. There should
be an open circuit, or at least 1 M
.
Go to step 8.
Replace the front passenger’s seat belt buckle
assembly, and clear the DTC.
8. Check resistance between the No. 1 terminal of the
right side wire harness 3P connector and body
ground. There should be 0
1
.
Go to step 9.
Open in the right side wire harness or poor
ground connection at G581. If G581 is OK, replace
the right side wire harness.
9. Disconnect the negative cable from the battery.
10. Disconnect SRS unit connector C (8P) from the SRS
unit.
(cont’d)
Terminal side of male terminals
Terminal side of male terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:01 61S0X050_230_0151
−
−
−
−
−
−
−
−
−
−
04
05
06
07
YES
NO
YES
NO
YES
NO
YES
NO
23-152
SRS
DTC Troubleshooting (cont’d)
RIGHT SIDE WIRE HARNESS 3P CONNECTOR
BLU
RIGHT SIDE WIRE HARNESS 3P CONNECTOR
YEL/BLU
RIGHT SIDE WIRE HARNESS
3P CONNECTOR
YEL/BLU
SRS UNIT CONNECTOR C (8P)
YEL/BLU
RIGHT SIDE WIRE HARNESS
3P CONNECTOR
SRS UNIT CONNECTOR C (8P)
BLU
BLU
11. Check resistance between the No. 2 terminal of the
right side wire harness 3P connector and body
ground. There should be an open circuit, or at least
1 M
.
Go to step 12.
Go to step 15.
12. Check resistance between the No. 3 terminal of the
right side wire harness 3P connector and body
ground. There should be an open circuit, or at least
1 M
.
Go to step 13.
Go to step 17.
13. Check resistance between the No. 7 terminal of
SRS unit connector C (8P) and the No. 3 terminal of
the right side wire harness 3P connector. There
should be 0
1
.
Go to step 14.
Go to step 19.
14. Check resistance between the No. 3 terminal of
SRS unit connector C (8P) and the No. 2 terminal of
the right side wire harness 3P connector. There
should be 0
1
.
Replace the SRS unit (see page 23-382).
Go to step 21.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:02 61S0X050_230_0152
−
−
−
−
*03
09
*04
11
YES
NO
YES
NO
23-153
A
C503
RIGHT SIDE WIRE HARNESS 3P CONNECTOR
BLU
A
C503
RIGHT SIDE WIRE HARNESS 3P CONNECTOR
YEL/BLU
15. Disconnect the SRS main harness 8P connector (A)
from the dashboard wire harness 8P connector
C503.
16. Check resistance between the No. 2 terminal of the
right side wire harness 3P connector and body
ground. There should be an open circuit, or at least
1 M
.
Short to ground in the SRS main harness or
SRS floor harness; replace the floor harness. If the
problem is still present; replace the SRS main
harness.
Short to ground in the right side wire harness
or dashboard wire harness; replace the faulty
harness.
17. Disconnect the SRS main harness 8P connector (A)
from the dashboard wire harness 8P connector
C503.
18. Check resistance between the No. 3 terminal of the
right side wire harness 3P connector and body
ground. There should be an open circuit, or at least
1 M
.
Short to ground in the SRS main harness or
SRS floor harness; replace the floor harness. If the
problem is still present; replace the SRS main
harness.
Short to ground in the right side wire harness
or dashboard wire harness; replace the faulty
harness.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:03 61S0X050_230_0153
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст