Honda Odyssey 2004. Manual — part 593
−
−
−
−
−
−
−
−
S0X4AZBK791000R8179FAAT00
S0X4ASIK791000R8579FAAT00
’03-04 Models
DTC 81-79:
’03-04 Models
DTC 85-79:
YES
NO
YES
NO
YES
NO
YES
NO
23-314
23-314
SRS
DTC Troubleshooting (cont’d)
Front Passenger’s Weight
Sensors Drift Check Failure
OPDS Sensor Drift Check Failure
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Turn the ignition switch OFF, and go to
step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Make sure nothing is on the front passenger’s seat.
4. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
The system is OK.
Remove the seat assembly (see page 20-81)
and front passenger’s weight sensors, then
reinstall them. Calibrate the front passenger’s
weight sensor unit (see page 23-42). Retry the
troubleshooting.
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Turn the ignition switch OFF, and go to
step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Make sure nothing is on the front passenger’s seat.
4. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
The system is OK.
Initialize the OPDS (see page 23-41). If the
problem is still present, replace the OPDS unit (see
page 23-387).
Does the SRS indicator stay on?
Does the SRS indicator go of f ?
Does the SRS indicator stay on?
Does the SRS indicator go of f ?
03/07/29 10:41:08 61S0X050_230_0314
−
−
−
−
−
−
−
−
S0X4ASIK791000R861XFAAT00
’03-04 Models
DTC 86-1x (86-10 to 86-19, 86-1A to 86-1F):
DTC 86-2x (86-20 to 86-29, 86-2A to 86-2F):
YES
NO
YES
NO
YES
NO
YES
NO
23-315
Faulty Seat-back Sensor
Faulty Support Sensor
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Check the connection at the OPDS sensor harness
connector and the OPDS unit connector.
Go to step 4.
Reconnect the OPDS sensor harness
connector, and clear the DTC.
4. Replace the OPDS sensor/seat back foam (see page
20-102), and reinitialize the OPDS (see page 23-41).
5. Erase the DTC memory, then check for DTC 86-1x
or 86-2x.
Go to step 6.
The system is OK.
6. Replace the OPDS unit (see page 23-387), and
reinitialize the OPDS.
7. Erase the DTC memory, then check for DTC 86-1x
or 86-2x.
Replace the SRS unit (see page 23-384).
The system is OK.
Does the SRS indicator stay on?
Ar e the connections OK ?
Is DT C 86-1x or 86-2x indicated?
Is DT C 86-1x or 86-2x indicated?
03/07/29 10:41:09 61S0X050_230_0315
−
−
−
−
−
−
01
02
S0X4ASIK791000R8731FAAT20
’03-04 Models
DTC 87-31:
YES
NO
YES
NO
YES
NO
23-316
SRS
DTC Troubleshooting (cont’d)
GRN
The Side Airbag Cutoff Indicator
Does Not Come On
1. Erase the DTC memory (see page 23-39).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Make sure nothing is
on the front passenger’s seat.
4. Check the No. 9 (10A) fuse in the driver’s under-
dash fuse/relay box.
Go to step 5.
Repair the short to ground in the No. 9 (10A)
fuse circuit.
5.
from the OPDS unit.
6. Turn the ignition switch ON (II).
7. Check for voltage between the No. 3 terminal of the
There should be battery voltage.
Faulty OPDS unit; replace the OPDS unit (see
page 23-387).
Go to step 8.
Wire side of female terminals
Does the side air bag cutof f indicator stay on?
Is the f use OK ?
Is ther e batter y voltage?
03/07/29 10:41:09 61S0X050_230_0316
D
Disconnect the OPDS unit harness 8P connector D
OPDS unit harness 8P connector D and body ground.
OPDS UNIT HARNESS 8P CONNECTOR D
−
−
03
04
YES
NO
23-317
GRN
GAUGE ASSEMBLY CONNECTOR A (14P)
A
B
8. Turn the ignition switch OFF.
9. Backprobe the No. 4 terminal of gauge assembly
connector A (14P). Do not disconnect gauge
assembly connector A (14P) from the gauge
assembly (see page 22-100).
10. Turn the ignition switch ON (II).
11. Check for voltage between the No. 4 terminal of
gauge assembly connector A (14P) and body
ground. There should be battery voltage.
Go to step 12.
Go to step 16.
12. Turn the ignition switch OFF.
13. Disconnect the right side wire harness 4P
connector (A) from the OPDS unit harness 4P
connector (B).
(cont’d)
Wire side of female terminals
Is ther e batter y voltage?
03/07/29 10:41:09 61S0X050_230_0317
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст