Honda Odyssey 2004. Manual — part 256
*01
S0X4AA1E10410424251KAAT30
Exploded View
14-418
Transmission End Cover
End Cover, 3rd Gear, Idler Gear, and 3rd Clutch Removal
TRANSMISSION
RANGE SWITCH
COVER
ATF HOSE
SEALING WASHERS
PARK GEAR
COUNTERSHAFT
3RD GEAR
TRANSMISSION
RANGE SWITCH
ATF LINE BOLT
END COVER
3RD CLUTCH
A/T CLUTCH PRESSURE
CONTROL SOLENOID
VALVE C
ATF FILTER LINE
BRACKET
ATF FILTER
LINE
A/T WIRE
HARNESS
GROUND TERMINAL
CONNECTOR
BRACKET
SWITCH
COVER
ATF
TEMPERATURE
SENSOR
ATF PASSAGE BODY
A/T CLUTCH PRESSURE
CONTROL SOLENOID
VALVES A and B
HARNESS
CLAMP
BRACKET
ATF COOLER
LINE BOLTS
ATF FILTER
ATF COOLER LINES
3RD CLUTCH
TRANSMISSION FLUID
PRESSURE SWITCH
CONNECTOR
SENSOR
CLAMP
HARNESS CLAMP
HARNESS CLAMP
LOCKNUT
PARK PAWL
THRUST NEEDLE
BEARING
SPLINED
WASHER
NEEDLE BEARING
THRUST
NEEDLE
BEARING
Replace.
03/07/29 09:45:41 61S0X050_140_0421
−
*02
*03
Special Tools Required
14-419
07GAB-PF50101 or
07GAB-PF50100
C
A
B
• Mainshaft holder
07GAB-PF50101 or 07GAB-PF50100
• Adjustable bearing puller, 25
40 mm
07736-A01000B or 07736-A01000A
NOTE: Refer to the exploded view as needed during the
following procedure.
1. Remove the ATF temperature sensor connector
from the connector bracket, then disconnect the
connector.
2. Remove the ATF temperature sensor harness
clamp bolts and the ATF temperature sensor, then
remove the switch cover.
3. Remove the A/T wire harness ground terminal from
the connector bracket, and disconnect the 3rd
clutch transmission fluid pressure switch connector,
then remove the connector bracket.
4. Remove the transmission range switch cover.
5. Remove the transmission range switch harness
clamp bolts and harness clamp, then remove the
transmission range switch.
6. Remove the harness clamp bracket, ATF cooler line
bolts (two), and lines.
7. Remove the line bolt, the ATF hose, and the ATF
filter line.
8. Remove the ATF filter line bracket and ATF filter.
Remove the ATF passage body if necessary.
9. Remove the A/T clutch pressure control solenoid
valve C.
10. Remove the remaining 10 bolts on the end cover,
then remove the end cover.
11. Slip the special tool onto the mainshaft.
12. Engage the park pawl with the park gear.
13. Cut the lock tabs (A) of each shaft locknut (B) using
a chisel (C). Then remove the locknuts and conical
spring washers from each shaft.
NOTE:
• Countershaft and secondary shaft locknuts have
left-hand threads.
• Clean the old locknut; they are used to install the
press fit mainshaft 3rd gear, secondary shaft
idler gear, park gear, and 3rd clutch assembly on
the countershaft.
• Keep all of the chiseled particles out of the
transmission.
14. Remove the special tool from the mainshaft.
(cont’d)
03/07/29 09:45:41 61S0X050_140_0422
−
−
*04
*05
*01
*02
S0X4AA1E10410445001MCAT00
Standard: 84.6
85.6 mm (3.33
3.37 in.)
PARK LEVER STOP
Mark
Part Number
L1
L2
14-420
14-420
Transmission End Cover
End Cover, 3rd Gear, Idler Gear, and
3rd Clutch Removal (cont’d)
Park Lever Stop Inspection and
Adjustment
07736-A01000B or
07736-A01000A
A
D
C
B
A
B
D
A
C
E
6 x 1.0 mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
L1
L2
E
15. Remove the 3rd clutch assembly using the special
tool and a commercially available 3/8-16’’ slide
hammer (A).
16. Remove the splined washer, thrust needle bearing,
countershaft 3rd gear, needle bearing, and thrust
needle bearing from the countershaft.
17. Remove the mainshaft 3rd gear (A), secondary
shaft idler gear (B), and park gear (C) with a puller
(D).
18. Remove the park pawl, park pawl spring, park pawl
shaft, and stop shaft.
19. Remove the park lever from the control shaft.
20. Remove A/T clutch pressure control solenoid
valves A and B.
1. Set the park lever (A) in the P position.
2. Measure the distance (B) between the park pawl
shaft (C) and the park lever roller pin (D).
3. If the measurement is out of tolerance, select and
install the appropriate park lever stop (E) from the
table.
1
24537-PA9-003
11.00 mm
(0.433 in.)
11.00 mm
(0.433 in.)
2
24538-PA9-003
10.80 mm
(0.425 in.)
10.65 mm
(0.419 in.)
3
24539-PA9-003
10.60 mm
(0.417 in.)
10.30 mm
(0.406 in.)
4. After replacing the park lever stop, make sure the
distance is within tolerance.
03/07/29 09:45:43 61S0X050_140_0423
01
02
S0X4AA1E10410417256KBAT00
01
02
S0X4AA1E10410417254KBAT00
Special Tools Required
Special Tools Required
14-421
14-421
Control Shaft Oil Seal Replacement
Control Shaft Bearing Replacement
A
B
07749-0010000
07746-0010800
07749-0010000
07746-0010800
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-0010800
1. Remove the oil seal (A) from the end cover (B).
2. Install the new oil seal flush to the end cover with
the special tools.
• Driver 07749-0010000
• Attachment, 22 x 24 mm 07746-0010800
1. Remove the oil seal from the end cover, then
remove the bearing.
2. Install the new bearing flush to the end cover with
the special tools.
3. Install the new oil seal.
03/07/29 09:45:43 61S0X050_140_0424
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст