Honda Odyssey 2004. Manual — part 452
*01
S0X4A00J32173660731FEAT00
Cavity
Test condition
Test: Desired result
Possible cause if result is not obtained
22-136
Turn Signal/Hazard Flasher
Turn Signal/Hazard Relay Input Test
B
A
1
3
2
1. Remove the driver’s under-dash fuse/relay box (see page 22-86).
2. Remove the turn signal/hazard relay (A) from the driver’s under-dash fuse/relay box (B).
3. Inspect the relay and fuse/relay box socket terminals to be sure they are all making good contact.
• If the terminals are bent, loose, or corroded, repair them as necessary, and recheck the system.
• If the terminals look OK, go to step 4.
4. Make these input tests at the fuse/relay box.
• If any test indicates a problem, find and correct the cause, then recheck the system.
• If all the input tests prove OK, the turn signal/hazard relay must be faulty; replace it.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1
Under all conditions
Check for continuity to ground:
There should be continuity.
Poor ground (G401)
An open in the wire
2
Ignition switch ON (II)
Check for voltage to ground:
There should be battery voltage.
Blown No. 10 (7.5A) fuse in the driver’s
under-dash fuse/relay box
Faulty hazard warning switch
An open in the wire
Hazard warning switch
ON
Check for voltage to ground:
There should be battery voltage.
Blown No. 49 (15A) fuse in the under-
hood fuse/relay box
Faulty hazard warning switch
An open in the wire
3
Ignition switch ON (II)
and turn signal switch
in Right or Left position
Connect No. 2 terminal to No. 3
terminal:
Right or left turn signal lights
should come on.
Poor ground (G201, G301, G552,
G582)
Faulty hazard warning switch
An open in the wire
Hazard warning switch
ON
Connect No. 2 terminal to No. 3
terminal:
Hazard warning lights should
come on.
Poor ground (G201, G301, G552,
G582)
Faulty hazard warning switch
An open in the wire
03/07/29 10:21:27 61S0X050_220_0138
01
01
S0X4A82J32173631001FEAT01
01
01
S0X4A83J32173631001FEAT02
With Navigation System
Without Navigation System
22-137
22-137
Hazard Warning Switch Test
B
C
A
D
A
B
C
D
Terminal
Position
ON
OFF
6
7
1
2
10
9
3
5
Terminal
Position
ON
OFF
6
1
2
10
3
5
4
8
1. Remove the center panel (see page 20-70).
2. Disconnect the 10P connector (A) from the hazard
warning switch (B).
3. Push out the hazard warning switch from behind
the center panel (C).
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the continuity is not as specified, replace the bulb
(D) or the switch.
1. Remove the instrument panel (see page 20-69).
2. Disconnect the 10P connector (A) from the hazard
warning switch (B).
3. Pull the hazard warning switch out from the clock
(C).
4. Check for continuity between the terminals in each
switch position according to the table.
5. If the continuity is not as specified, replace the bulb
(D) or the switch.
03/07/29 10:21:28 61S0X050_220_0139
*01
S0X4A00J32323300000DAAT00
22-138
Entry Lights Control System
Component Location Index
PASSENGER’S DOOR SWITCH
RIGHT REAR INDIVIDUAL MAP LIGHTS
DRIVER’S DOOR SWITCH
IGNITION KEY SWITCH
INTERIOR LIGHTS RELAY
LEFT SLIDING DOOR SWITCH
LEFT REAR INDIVIDUAL MAP LIGHTS
RIGHT SLIDING DOOR SWITCH
INTERIOR LIGHTS SWITCH
IGNITION KEY LIGHT
Test, page 22-150
Test, page 22-145
Wire colors: BLK/BLU,
WHT/BLU, LT GRN, BLK
Test, page 22-88
Test, page 22-150
Test, page 22-148
NOTE: Entry Light Control System is on EX and EXL models.
Test, page 22-145
03/07/29 10:21:30 61S0X050_220_0140
For LX model, refer to Safety Indicator System page 22-103.
*01
S0X4A00J32323300000EAAT00
−
−
−
−
22-139
Circuit Diagram
GRN/WHT
GRN
GRY/YEL
GRY/YEL
GRN
GRN/WHT
GRN/ORN
GRN/ORN
BLK/BLU
BLK
G401
B9
B1
PNK
BRN
A2
A15
LT GRN
DOOR
•
G401
BLK
2
3
A17
BLK/RED
GRY/YEL
A17
A14
GRN/WHT
YEL
A22
A21
A24
A6
A1
RED/BLK
(10A)
No.9
No.11
(10A)
BLK/YEL
IG1
BAT
IGNITION SWITCH
WHT
YEL
6
7
No.42 (50A)
No.47
(20A)
GRN
A16
GRN/ORN
BLU/WHT
3
1
BLK
G401
A16
A13
WHT/BLK
WHT/YEL
UNDER HOOD FUSE/RELAY BOX
No.54 (40A)
No.41 (120A)
BATTERY
BLK/WHT
WHT/BLU
OFF
ON
PASSENGER’S
UNDER DASH
FUSE/RELAY BOX
DRIVER’S
UNDER DASH
FUSE/RELAY
BOX
INTERIOR
LIGHTS
RELAY
INTERIOR
LIGHTS
SWITCH
IGNITION
KEY
LIGHT
(LED)
•
(Fuse/relay
box socket)
DOOR
MULTIPLEX
CONTROL UNIT
DRIVER’S MULTIPLEX
CONTROL UNIT
PASSENGER’S MULTIPLEX
CONTROL UNIT
SAFETY
INDICATOR
SYSTEM
SAFETY
INDICATOR
SYSTEM
SAFETY
INDICATOR
SYSTEM
SAFETY
INDICATOR
SYSTEM
DRIVER’S
DOOR LOCK
KNOB
SWITCH
UN
LOCK
IGNITION
KEY
SWITCH
(Closed :
Key inserted)
DRIVER’S
DOOR
SWITCH
(Closed :
Door open)
LEFT SLIDING
DOOR
SWITCH
(Closed :
Door open)
PASSENGER’S
DOOR
SWITCH
(Closed :
Door open)
RIGHT SLIDING
DOOR
SWITCH
(Closed :
Door open)
CEILING
LIGHTS
TAILLIGHT RELAY
COMBINATION
LIGHT SWITCH
03/07/29 10:21:31 61S0X050_220_0141
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст