Honda Odyssey 2004. Manual — part 557
−
−
−
−
03
01
*01
02
YES
NO
YES
NO
23-170
SRS
DTC Troubleshooting (cont’d)
B
SRS UNIT CONNECTOR B (18P)
C852
A
SRS FLOOR SUBHARNESS 28P CONNECTOR
11. Disconnect SRS unit connector B (18P) from the
SRS unit.
12. Check resistance between the No. 17 and No. 15
terminals of SRS unit connector B (18P), and
between the No. 17 and No. 16 terminals, and
between the No. 17 terminal and body ground.
There should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 13.
13. Disconnect the SRS floor subharness 28P
connector (A) from the SRS floor harness 28P
connector C852.
14. Check resistance between the No. 22 and No. 17
terminals of the SRS floor subharness 28P
connector, and between the No. 22 and No. 27
terminals. Then check resistance between the No.
22 terminal and body ground. There should be
1 M
or more.
Short to ground in the SRS floor harness;
replace the SRS floor harness.
Short to ground in the SRS floor subharness
or left side wire harness; replace the faulty
harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:16 61S0X050_230_0170
−
−
−
−
01
02
S0X4AC5K79100081121FAAT20
’02 Model
DTC 12-1:
Special Tools Required
YES
NO
YES
NO
23-171
07XAZ-S1A0200
07SAZ-TB4011A
B
A
A
Open or Increased Resistance in
Front Passenger’s Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the right side wire harness 2P
connector (A) from the front passenger’s side
airbag (B).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Open or increased resistance in the front
passenger’s side airbag inflator, replace the front
passenger’s side airbag (see page 23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s side airbag 2P connector (A).
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-1 indicated?
03/07/29 10:36:17 61S0X050_230_0171
−
−
−
−
−
−
03
01
*01
02
YES
NO
YES
NO
23-172
SRS
DTC Troubleshooting (cont’d)
B
SRS UNIT CONNECTOR B (18P)
C852
A
SRS FLOOR SUBHARNESS 28P CONNECTOR
11. Disconnect SRS unit connector B (18P) from the
SRS unit. Do not disconnect the special tool from
the right side wire harness 2P connector.
12. Check resistance between the No. 7 and No. 17
terminals of SRS unit connector B (18P). There
should be 2.0
3.0
.
Faulty SRS unit or poor contact at SRS unit
connector B (18P) and the SRS unit; check the
connection; if the connector is OK, replace the SRS
unit (see page 23-382).
Go to step 13.
13. Disconnect the SRS floor subharness 28P
connector (A) from the SRS floor harness 28P
connector C852.
14. Check resistance between the No. 23 and No. 24
terminals of the SRS floor subharness 28P
connector. There should be 2.0
3.0
.
Open or increased resistance in the SRS
floor harness; replace the SRS floor harness.
Open or increased resistance in the SRS floor
subharness or right side wire harness; replace the
faulty harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:18 61S0X050_230_0172
−
−
−
−
01
02
S0X4AC5K79100081123FAAT00
’02 Model
DTC 12-3:
Special Tools Required
YES
NO
YES
NO
23-173
07XAZ-S1A0200
07SAZ-TB4011A
B
A
A
Short to Another Wire or
Decreased Resistance in Front Passenger’s
Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the right side wire harness 2P
connector (A) from the front passenger’s side
airbag (B).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to another wire in the front passenger’s
side airbag inflator; replace the front passenger’s
side airbag (see page 23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s side airbag 2P connector (A).
11. Disconnect the special tool from the right side wire
harness 2P connector.
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-3 indicated?
03/07/29 10:36:19 61S0X050_230_0173
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст