Honda Odyssey 2004. Manual — part 558
−
−
−
−
03
01
*01
02
YES
NO
YES
NO
23-174
SRS
DTC Troubleshooting (cont’d)
B
SRS UNIT CONNECTOR B (18P)
C852
A
SRS FLOOR SUBHARNESS 28P CONNECTOR
12. Disconnect SRS unit connector B (18P) from the
SRS unit.
13. Check resistance between the No. 7 and No. 18
terminals of SRS unit connector B (18P). There
should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 14.
14. Disconnect the SRS floor subharness 28P
connector (A) from the SRS floor harness 28P
connector C852.
15. Check resistance between the No. 23 and No. 24
terminals of the SRS floor subharness 28P
connector. There should be an open circuit, or at
least 1 M
.
Short in the SRS floor harness; replace the
SRS floor harness.
Short in the SRS floor subharness or right
side wire harness; replace the faulty harness.
Wire side of female terminals
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:36:19 61S0X050_230_0174
−
−
−
−
01
02
S0X4AC5K79100081124FAAT00
’02 Model
DTC 12-4:
Special Tools Required
YES
NO
YES
NO
23-175
07XAZ-S1A0200
07SAZ-TB4011A
B
A
A
Short to Power in Front Passenger’s
Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the right side wire harness 2P
connector (A) from the front passenger’s side
airbag (B).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the front passenger’s side
airbag inflator; replace the front passenger’s side
airbag (see page 23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s side airbag 2P connector (A).
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-4 indicated?
03/07/29 10:36:20 61S0X050_230_0175
−
−
−
−
03
01
*01
02
YES
NO
YES
NO
23-176
SRS
DTC Troubleshooting (cont’d)
B
SRS UNIT CONNECTOR B (18P)
C852
A
SRS FLOOR SUBHARNESS 28P CONNECTOR
11. Disconnect SRS unit connector B (18P) from the
SRS unit.
12. Turn the ignition switch ON (II).
13. Check for voltage between the No. 8 terminal of
SRS unit connector B (18P) and body ground, and
between the No. 18 terminal and body ground.
There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 14.
14. Turn the ignition switch OFF.
15. Disconnect the SRS floor subharness 28P
connector (A) from the SRS floor harness 28P
connector C852.
16. Turn the ignition switch ON (II).
17. Check for voltage between the No. 23 terminal of
the SRS floor subharness 28P connector and body
ground, and between the No. 24 terminal and body
ground. There should be 0.5 V or less.
Short to power in the SRS floor harness;
replace the SRS floor harness.
Short to power in the SRS floor subharness or
right side wire harness; replace the faulty
harness.
Wire side of female terminals
Wire side of female terminals
Is the voltage as specif ied?
Is the voltage as specif ied?
03/07/29 10:36:21 61S0X050_230_0176
−
−
−
−
01
02
S0X4AC5K79100081125FAAT00
’02 Model
DTC 12-5:
Special Tools Required
YES
NO
YES
NO
23-177
07XAZ-S1A0200
07SAZ-TB4011A
B
A
A
Short to Ground in Front
Passenger’s Side Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead E 07XAZ-S1A0200
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the right side wire harness 2P
connector (A) from the front passenger’s side
airbag (B).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to ground in the front passenger’s side
airbag inflator; replace the front passenger’s side
airbag (see page 23-372).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver’s side airbag 2P connector (A).
(cont’d)
Does the SRS indicator stay on?
Is DT C 12-5 indicated?
03/07/29 10:36:21 61S0X050_230_0177
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст