Honda Odyssey 2004. Manual — part 546
−
−
03
04
05
YES
NO
23-126
SRS
DTC Troubleshooting (cont’d)
A
B
C
A
SRS UNIT CONNECTOR A (18P)
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and front
passenger’s seat belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit.
18. Disconnect the special tool from the SRS main
harness 2P connector.
19. Reconnect the battery negative cable.
20. Turn the ignition switch ON (II).
21. Check for voltage between the No. 8 terminal of
SRS unit connector A (18P) and body ground, and
between the No. 17 terminal and body ground.
There should be 0.5 V or less.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 22.
Wire side of female terminals
Is the voltage as specif ied?
03/07/29 10:34:43 61S0X050_230_0126
−
−
*02
07
YES
NO
23-127
C851
A
SRS MAIN HARNESS 28P CONNECTOR
22. Turn the ignition switch OFF.
23. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
24. Turn the ignition switch ON (II).
25. Check for voltage between the No. 5 terminal of the
SRS main harness 28P connector and body ground,
and between the No. 14 terminal and body ground.
There should be 0.5 V or less.
Short to power in the SRS floor harness;
replace the SRS floor harness.
Short to power in the SRS main harness;
replace the SRS main harness.
Wire side of female terminals
Is the voltage as specif ied?
03/07/29 10:34:43 61S0X050_230_0127
−
−
−
−
−
−
01
*01
S0X4AZ3K79100081035FAAT00
’02 Model
DTC 3-5:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-128
SRS
DTC Troubleshooting (cont’d)
A
07TAZ-SZ5011A
07SAZ-TB4011A
A
C551
07TAZ-
SZ5011A
07SAZ-TB4011A
Short to Ground in Driver’s Seat Belt
Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s seat belt tensioner 2P
connector from the left side wire harness 2P
connector (A).
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to ground in the driver’s seat belt
tensioner; replace the driver’s seat belt (see page
23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the SRS main harness 2P connector
C551 from the left side wire harness 2P
connector (A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to ground in the left side wire harness;
replace the left side wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Does the SRS indicator stay on?
Is DT C 3-5 indicated?
Is DT C 3-5 indicated?
03/07/29 10:34:44 61S0X050_230_0128
−
−
03
04
05
YES
NO
23-129
A
B
C
A
SRS UNIT CONNECTOR A (18P)
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and front
passenger’s seat belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit.
18. Disconnect the special tool from the SRS main
harness 2P connector.
19. Check resistance between the No. 8 terminal of
SRS unit connector A (18P) and body ground, and
between the No. 17 terminal and body ground.
There should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 20.
(cont’d)
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:34:45 61S0X050_230_0129
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст