Honda Odyssey 2004. Manual — part 545
−
−
−
−
−
−
01
*01
S0X4AZ3K79100081033FAAT00
’02 Model
DTC 3-3:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-122
SRS
DTC Troubleshooting (cont’d)
A
07TAZ-SZ5011A
07SAZ-TB4011A
A
C551
07TAZ-
SZ5011A
07SAZ-TB4011A
Short to Another Wire or Decreased
Resistance in Driver’s Seat Belt Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s seat belt tensioner 2P
connector from the left side wire harness 2P
connector (A).
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short in the driver’s seat belt tensioner;
replace the driver’s seat belt (see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the SRS main harness 2P connector
C551 from the left side wire harness 2P connector
(A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short in the left side wire harness; replace the
left side wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Does the SRS indicator stay on?
Is DT C 3-3 indicated?
Is DT C 3-3 indicated?
03/07/29 10:34:40 61S0X050_230_0122
−
−
03
04
05
YES
NO
23-123
A
B
C
A
SRS UNIT CONNECTOR A (18P)
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and front
passenger’s seat belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit.
18. Disconnect the special tool from the SRS main
harness 2P connector.
19. Check resistance between the No. 8 and the No. 17
terminals of the SRS unit connector A (18P). There
should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 20.
(cont’d)
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:34:41 61S0X050_230_0123
−
−
*02
07
YES
NO
23-124
SRS
DTC Troubleshooting (cont’d)
C851
A
SRS MAIN HARNESS 28P CONNECTOR
20. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
21. Check resistance between the No. 5 and the No. 14
terminals of the SRS main harness 28P connector.
There should be an open circuit, or at least 1 M
.
Short in the SRS floor harness; replace the
SRS floor harness.
Short in the SRS main harness; replace the
SRS main harness.
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:34:41 61S0X050_230_0124
−
−
−
−
−
−
01
*01
S0X4AZ3K79100081034FAAT00
’02 Model
DTC 3-4:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-125
A
07TAZ-SZ5011A
07SAZ-TB4011A
A
C551
07TAZ-
SZ5011A
07SAZ-TB4011A
Short to Power in Driver’s Seat Belt
Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s seat belt tensioner 2P
connector from the left side wire harness 2P
connector (A).
5. Connect the special tool (2
connector) to the left
side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the driver’s seat belt
tensioner; replace the driver’s seat belt (see page
23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the SRS main harness 2P connector
C551 from the left side wire harness 2P connector
(A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to power in the left side wire harness;
replace the left side wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
(cont’d)
Does the SRS indicator stay on?
Is DT C 3-4 indicated?
Is DT C 3-4 indicated?
03/07/29 10:34:42 61S0X050_230_0125
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст