Honda Odyssey 2004. Manual — part 607
01
02
01
02
S0X4A00H46400012803KBAT00
Removal (’99-01 Models)
Removal (’02-04 Models)
23-370
SRS
Front Passenger’s Airbag Replacement
A
B
B
A
B
A
B
A
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Remove the glove box (see page 20-71), then
disconnect the connector between the SRS main
harness 2P connector (A) and the front passenger’s
airbag 2P connector (B).
3. Remove the four mounting nuts (A) from the
bracket. Cover the lid and dashboard with a cloth,
and pry carefully with a screwdriver to lift the front
passenger’s airbag (B) out of the dashboard.
NOTE: The airbag lid has pawls on its side which
attach it to the dashboard.
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Remove the glove box (see page 20-71).
3. Disconnect the connector between the front
passenger’s airbag 4P connector (A) and the
dashboard wire harness B 4P connector (B).
4. Remove the four mounting nuts (A) from the
bracket. Cover the lid and dashboard with a cloth,
and pry carefully with a screwdriver to lift the front
passenger’s airbag (B) out of the dashboard.
NOTE: The airbag lid has pawls on its side which
attach it to the dashboard.
03/07/29 10:42:45 61S0X050_230_0370
03
04
03
04
Installation (’99-01 Models)
Installation (’02-04 Models)
23-371
A
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
A
C
A
B
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
B
A
1. Place the new front passenger’s airbag (A) into the
dashboard. Tighten the front passenger’s airbag
mounting nuts (B).
2. Connect the front passenger’s airbag 2P connector
(A) to the SRS main harness 2P connector (B).
Attach the front passenger’s airbag connector to
the connector holder (C), then reinstall the glove
box.
3. Reconnect the battery negative cable.
4. After installing the airbag, confirm proper system
operation: Turn the ignition switch ON (II); the SRS
indicator should come on for about 6 seconds and
then go off.
1. Place the new front passenger’s airbag (A) into the
dashboard. Tighten the front passenger’s airbag
mounting nuts (B).
2. Connect the front passenger’s airbag 4P connector
(A) to the SRS main harness 4P connector (B), then
reinstall the glove box.
3. Reconnect the battery negative cable.
4. After installing the airbag, confirm proper system
operation: Turn the ignition switch ON (II); the SRS
indicator should come on for about 6 seconds and
then go off.
03/07/29 10:42:45 61S0X050_230_0371
01
02
03
S0X4ASHH46400055381KBAT00
’02-04 Models
Removal
Installation
23-372
SRS
Side Airbag Replacement
A
B
A
B
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
NOTE: Review the seat replacement procedure (see
page 20-81) before performing repair or service.
1. Disconnect the battery negative cable, and wait at
least 3 minutes before beginning work.
2. Disconnect the side airbag harness 2P
connector (A).
3. Remove the seat assembly (see page 20-81) and
seat-back cover (see page 20-102).
4. Remove the mounting nuts (A) and the side
airbag (B).
NOTE:
• If the side airbag lid is secured by a tape, remove the
tape.
• Do not open the lid of the side airbag cover.
• Use new mounting nuts tightened to the specified
torque.
• Make sure that the seat-back cover is installed
properly. Improper installation may prevent proper
deployment.
• Be sure to install the harness wires so they are not
pinched or interfering with other parts.
1. Place the new side airbag on the seat-back frame
(A). Tighten the side airbag mounting nuts (B).
2. Install the seat-back cover (see page 20-102).
3. Install the seat assembly (see page 20-81), then
connect the side airbag harness 2P connector.
4. Move the front seat and the seat-back through their
full ranges of movement, making sure the harness
wires are not pinched or interfering with other parts.
5. Reconnect the battery negative cable.
6. After installing the side airbag, confirm proper
system operation: Turn the ignition switch ON (II);
the SRS indicator should come on for about 6
seconds and then go off.
03/07/29 10:42:46 61S0X050_230_0372
01
02
S0X4A00H46400012802LBAT00
Special Tool Required
Driver’s Airbag
Front Passenger’s Airbag
Deploying Airbags in the vehicle
23-373
Airbag Disposal
B
C
A
B
A
Deployment tool 07HAZ-SG00500
Before scrapping any airbags, side airbags, or seat belt
tensioners, (including those in a whole vehicle to be
scrapped), the airbags, side airbags, or seat belt
tensioners, must be deployed. If the vehicle is still
within the warranty period, the Honda District Service
Manager must give approval and/or special instruction
before deploying the airbags, or side airbags, seat belt
tensioners. Only after the airbags, side airbags, or seat
belt tensioners have been deployed (as the result of
vehicle collision, for example), can they be scrapped.
If the airbags, side airbags, and seat belt tensioners
appear intact (not deployed), treat them with extreme
caution. Follow this procedure.
If an SRS equipped vehicle is to be entirely scrapped, its
airbags, side airbags, and seat belt tensioners, should
be deployed while still in the vehicle. The airbags, side
airbags and seat belt tensioners should not be
considered as salvageable parts and should never be
installed in another vehicle.
1. Turn the ignition switch OFF, then disconnect the
battery negative cable, and wait at least 3 minutes.
2. Confirm that each airbag, side airbag, or seat belt
tensioner is securely mounted.
3. Confirm that the special tool is functioning properly
by following the check procedure on the tool label.
4. Remove the access panel (A), then disconnect the
4P connector between the driver’s airbag (B) and
the cable reel (C).
5. Remove the glove box (see page 20-71), then
disconnect the 4P connector between the front
passenger’s airbag (A) and dashboard wire harness
(B).
(cont’d)
03/07/29 10:42:47 61S0X050_230_0373
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст