Honda Odyssey 2004. Manual — part 608
*01
06
Deploying Components Out of the Vehicle
Disposal of Damaged Components
Deployment Tool Check
23-375
A
10. Connect a 12 volt battery to the tool.
• If the green light on the tool comes on, the igniter
circuit is defective and cannot deploy the
component. Go to Disposal of Damaged
Components.
• If the red light on the tool comes on, the
component is ready to be deployed.
11. Push the tool’s deployment switch. The airbags and
tensioners should deploy (deployment is both
highly audible and visible: a loud noise and rapid
inflation of the bag, followed by slow deflation).
• If the components deploy and the green light on
the tool comes on, continue with this procedure.
• If a component doesn’t deploy, yet the green
light comes ON, its igniter is defective. Go to
Disposal of Damaged Components.
• During deployment the airbag can become hot
enough to burn you. Wait 30 minutes after
deployment before touching the airbag.
12. Dispose of the complete airbag. No part of it can be
reused. Place it in a sturdy plastic bag (A), and seal
it securely.
If an intact airbag or tensioner has been removed from
a scrapped vehicle, or has been found defective or
damaged during transit, storage, or service, it should be
deployed as follows:
1. Confirm that the special tool is functioning properly
by following the check procedure on this page or
on the tool label.
2. Position the airbag face up, outdoors, on flat
ground, at least 30 feet (10 meters) from any
obstacles or people.
3. Follow steps 9, 10, 11, and 12 of the in-vehicle
deployment procedure.
1. If installed in a vehicle, follow the removal
procedure for the driver’s airbag (see page 23-368),
front passenger’s airbag (see page 23-370), side
airbag (see page 23-372), and seat belt tensioner
(see page 23-4).
2. In all cases, make a short circuit by twisting
together the two inflator wires.
’02-04 Models:
NOTE: The driver’s and passenger’s airbag each
have four wires: twist each pair of like-colored
wires together
3. Package the component in exactly the same
packaging that the new replacement part came in.
4. Mark the outside of the box ’’DAMAGED AIRBAG
NOT DEPLOYED’’, ’’DAMAGED SIDE AIRBAG NOT
DEPLOYED’’ or ’’DAMAGED SEAT BELT
TENSIONER NOT DEPLOYED’’ so it does not get
confused with your parts stock.
5. Contact your Honda District Service Manager for
how and where to return it for disposal.
1. Connect the yellow clips to both switch protector
handles on the tool; connect the tool to a battery.
2. Push the operation switch: green means the tool is
OK; red means the tool is faulty.
3. Disconnect the battery and the yellow clips.
03/07/29 10:42:49 61S0X050_230_0375
03
04
S0X4A00H46400016251KBAT00
Removal (’99-01 Models)
23-376
SRS
Cable Reel Replacement
A
A
C
B
1. Make sure the front wheels are aligned straight
ahead.
2. Disconnect the battery negative cable, and wait at
least 3 minutes.
3. Remove the driver’s airbag (see page 23-368).
4. Remove the steering wheel (see page 17-22).
5. Remove the dashboard lower cover (A).
6. Remove the column cover screws (A), then remove
the column covers (B, C).
03/07/29 10:42:49 61S0X050_230_0376
05
06
01
Removal (’02-04 Models)
23-377
D
C
A
B
A
B
A
7. Disconnect the SRS main harness 2P connector (A)
from the cable reel 2P connector (B), then
disconnect the dashboard wire harness 4P
connector (C) from the cable reel (D).
8. Remove the screws (A) from the cable reel, then
remove the cable reel from the column.
1. Make sure the front wheels are aligned straight
ahead.
2. Disconnect the battery negative cable, and wait at
least 3 minutes.
3. Remove the driver’s airbag (see page 23-368).
4. Disconnect the connectors (A) from the cruise
control set/resume switch, radio remote switch,
and horn switch, then remove the steering wheel
bolt (B).
5. Remove the steering wheel with a steering wheel
puller (see step 3 on page 17-22). Do not tap on the
steering wheel or steering column shaft when
removing the steering wheel.
(cont’d)
03/07/29 10:42:50 61S0X050_230_0377
02
03
04
05
23-378
SRS
Cable Reel Replacement (cont’d)
A
B
C
A
A
B
B
A
6. Remove the dashboard lower cover (A).
7. Remove the column cover screws (A), then remove
the column covers (B, C).
8. Disconnect the SRS main harness 4P connectors
(A) from the cable reel 4P connectors (B).
9. Release the tab (A), then remove the cable reel
from the column.
03/07/29 10:42:51 61S0X050_230_0378
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст