Honda Odyssey 2004. Manual — part 356
03
04
20-66
Interior Trim
Carpet Replacement (cont’d)
Fastener Locations
: Bolt, 2
8 x 1.25 mm
22 N·m
(2.2 kgf·m,
16 lbf·ft)
A
Fastener Locations
: Clip, 2
D
A
C
C
E
C
B
A
4. For Van: Remove the bolts and remove the floor
recess lid (A).
5. Remove the clips and release the retainers (A),
hook (B) and fasteners (C), then remove the front
carpet (D) and rear carpet (E). Put on gloves to
protect your hands.
6. Install the carpet in the reverse order of removal,
and note these items:
• Take care not to damage, wrinkle or twist the
carpet.
• Make sure the seat harness is routed correctly.
• Slip the slits in the carpet over the hooks.
• Replace any damaged clips.
• Push the clips into place securely.
03/07/29 10:01:48 61S0X050_200_0068
01
01
02
02
S0X4A00J26216516455KDAT00
’02-04 models with navigation system
20-67
Consoles
Center Lower Pocket Removal/Installation
Fastener Locations
: Clip, 2
A
B
: Clip, 3
A
B
B
A
C
C
D
B
Fastener Locations
: Clip, 6
A
B
A
Fastener Locations
: Screw, 6
: Clip, 2
A
SRS components are located in this area. Review the
SRS component locations, ’99-01 models (see page 23-
18), ’02 model (see page 23-19), ’03-04 models (see
page 23-20), and the precautions and procedures (see
page 23-21) before performing repairs or service.
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts, to prevent damage.
• Take care not to scratch the dashboard and related
parts.
1. Remove the clips (A), and detach the clips (B) and
tabs (C), then remove the center lower trim (D).
2. For ’02-04 models with navigation system: Detach
the clips, then remove the DVD panel (A).
3. Remove the center lower pocket (A).
–1 Remove the screws.
–2 Gently pull out along the top of the center
lower pocket to release the clips.
–3 Disconnect the center lower pocket light
connector (B) (except ’02-04 models with
navigation system).
4. Install the pocket in the reverse order of removal,
and note these items:
• Replace any damaged clips.
• Make sure the center lower pocket light
connector is plugged in properly.
• Push the clips into place securely.
03/07/29 10:01:49 61S0X050_200_0069
01
S0X4A00J26216516451KDAT00
20-68
Consoles
Center Lower Console Removal/Installation
Fastener Locations
Screw, 4
B
A
SRS components are located in this area. Review the
SRS component locations, ’99-01 models (see page 23-
18), ’02 model (see page 23-19), ’03-04 models (see
page 23-20), and the precautions and procedures (see
page 23-21) before performing repairs or service.
NOTE: Take care not to scratch the dashboard and
related parts.
1. Remove the center lower pocket (see page 20-67).
2. For some ’02-04 models: Remove the DVD player
unit (see page 22-342).
3. Remove the center lower console (A).
–1 Remove the screws.
–2 Gently pull out the console.
–3 Disconnect the accessory socket connector (B),
and remove the console.
4. Install the console in the reverse order of removal,
and make sure the accessory socket connector is
plugged in properly.
03/07/29 10:01:50 61S0X050_200_0070
01
S0X4A00J26220234701KDAT00
01
S0X4A00J26220219301KDAT00
20-69
20-69
Dashboard
Instrument Panel Removal/
Installation
Dashboard Lower Cover Removal/
Installation
Fastener Locations
B
A
B
D
E
: Screw, 8
B
: Clip, 3
C
: Clip, 1
B
C
Fastener Locations
: Screw, 1
: Clip, 3
A
B
C
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts, to prevent damage.
• Take care not to scratch the dashboard and related
parts.
1. Remove these items:
• Driver’s switch panel (see page 20-70)
• Center panel (see page 20-70)
2. Tilt the steering column down.
3. Remove the instrument panel (A).
–1 Remove the screws.
–2 Gently pull out along the top to release the
clips (B, C).
–3 Disconnect the hazard warning switch
connector (D) and clock connector (E). With
navigation system, disconnect the climate
control unit connector.
4. Install the instrument panel in the reverse order of
removal, and note these items:
• Make sure each connector is plugged in properly.
• Push the clips into place securely.
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts, to prevent damage.
• Take care not to scratch the dashboard and related
parts.
1. Remove the dashboard lower cover (A).
–1 Remove the screw.
–2 Gently pull down on the lower cover to release
the clips.
–3 If equipped, disconnect the air hose (B) and in-
car temperature sensor connector (C), then
remove the cover.
2. Install the lower cover in the reverse order of
removal, and note these items:
• Make sure the in-car temperature sensor
connector is plugged in properly, and the air
hose is connected properly (for some models).
• Push the clips into place securely.
03/07/29 10:01:50 61S0X050_200_0071
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст