Honda Odyssey 2004. Manual — part 357
*01
S0X4A00J26220222271KDAT00
01
S0X4A00J26220219291KDAT00
20-70
20-70
Dashboard
Driver’s Switch Panel Removal/
Installation
Center Panel Removal/Installation
A
Fastener Locations
: Clip, 5
B, C
D
E
B
C
F
G
B
C
C
Fastener Locations
: Clip, 10
B
C
D
A
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts, to prevent damage.
• Take care not to scratch the dashboard and related
parts.
1. Gently pull out on the driver’s switch panel (A) to
release the right clips (B), then detach the
remaining clips (C). If equipped, disconnect the
cruise control main switch connector (D), TCS
switch connector (E), power mirror switch
connector (F) and power sliding door switch
connector (G), then remove the panel.
2. Install the panel in the reverse order of removal,
and note these items:
• Make sure each connector is plugged in properly
(if equipped).
• Push the clips into place securely.
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts, to prevent damage.
• Take care not to scratch the dashboard and related
parts.
1.
page 17-25).
2. Carefully detach the clips, then remove the center
panel (A). Disconnect the heater control panel
connectors (B) or climate control unit connectors,
rear A/C control dial (C) (for some models) and
interior light switch connector (D). With navigation
system, disconnect the hazard warning switch
connector, rear A/C control dial, and interior light
switch connector. For ’03-04 models: Disconnect
the passenger’s airbag off indicator connector.
3. Install the panel in the reverse order of removal,
and note these items:
• Make sure each connector is plugged in properly.
• Push the clips into place securely.
03/07/29 10:01:51 61S0X050_200_0072
Remove the steering column covers (see step 4 on
01
01
S0X4A00J26220230101KDAT00
20-71
Glove Box Removal/Installation
B
A
Fastener Locations
: Bolt, 2
5 x 0.8 mm
9 N·m
(0.9 kgf·m,
7 lbf·ft)
A
SRS components are located in this area. Review the
SRS component locations, ’99-01 models (see page 23-
18), ’02 model (see page 23-19), ’03-04 models (see
page 23-20), and the precautions and procedures (see
page 23-21) before performing repairs or service.
NOTE:
• Take care not to scratch the dashboard and related
parts.
• If the glove box swings down without any support,
the hinges can be overextended and damaged. To
prevent damage to the glove box hinge, use a piece
of foam or a bundle of shop towels to support it.
1. While holding the glove box (A), remove the glove
box stop (B) on each side.
2. Remove the bolts, then remove the glove box (A).
3. Install the glove box in the reverse order of
removal.
03/07/29 10:01:52 61S0X050_200_0073
21
S0X4A00J26220219251KDAT20
*01
S0X4A00J26220214551KDAT00
20-72
20-72
Dashboard
Passenger’s Side Vent Removal/
Installation
Beverage Holder Base Removal/
Installation
D
E
A
B
C
Fastener Locations
: Screw, 3
D
: Screw, 2
E
C
B
D
D
E
A
E
D
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts to prevent damage.
• Take care not to scratch the dashboard and related
parts.
1. Remove the passenger’s side vent (A).
–1 Carefully insert a flat-tip screwdriver next to
the right pivot (B).
–2 Release the pivot by prying on the vent.
–3 Remove the vent by releasing the left pivot
portion (C).
2. Before reinstalling, make sure the left pivot
bushing (D) is installed on the side vent housing (E)
securely.
3. Reinstall the left pivot portion of the vent to the
bushing first, then push the right pivot portion into
place securely.
NOTE:
• Take care not to scratch the dashboard and related
parts.
• Put on gloves to protect your hands.
1. Make sure you have the anti-theft codes for the
radio and the navigation system, then write down
the frequencies for the preset buttons.
2. Remove these items:
• Center lower console (see page 20-68)
• Center panel (see page 20-70)
• Audio unit (see page 22-159)
• Display unit (with navigation system) (see page
22-385)
3. Remove the beverage holder base (A).
–1 Detach the hook (B) from under the beverage
holder (C).
–2 Pull the beverage holder out.
–3 Remove the screws (D, E).
–4 Remove the beverage holder base from the
center lower console opening.
4. Install the beverage holder base in the reverse
order of removal, and enter the anti-theft code for
the radio and the navigation system, then enter the
customer’s radio station presets.
03/07/29 10:01:52 61S0X050_200_0074
*01
02
03
S0X4A00J26220200000KDAT00
20-73
Dashboard Removal/Installation
Fastener Locations
: Screw, 1
: Clip, 2
A
B
Fastener Locations
: Screw, 1
B
: Clip, 4
C
: Clip, 3
B
B
C
D
A
D
C
C
B
B
Fastener Location
: Bolt, 1
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
SRS components are located in this area. Review the
SRS component locations, ’99-01 models (see page 23-
18), ’02 model (see page 23-19), ’03-04 models (see
page 23-20), and the precautions and procedures (see
page 23-21) before performing repairs or service.
NOTE:
• When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the
related parts to prevent damage.
• Have an assistant help you when removing and
installing the dashboard.
• Take care not to scratch the dashboard, body or other
related parts.
• Put on gloves to protect your hands.
1. Make sure you have the anti-theft codes for the
radio and the navigation system, then write down
the frequencies for the preset buttons.
2. Disconnect the negative battery cable, and wait at
least 3 minutes before beginning work.
3. Remove these items:
• Dashboard lower cover (see page 20-69)
• Steering column (see page 17-25)
• Center lower pocket (see page 20-67)
• Heater lower cover, both sides (see step 2 on
page 20-65)
• Glove box (see page 20-71)
4. Remove these items (see page 20-58):
• Front door opening trim, both sides
• Kick panel, both sides
• Front pillar trim, both sides
5. Open the driver’s door, and remove the front pillar
corner trim (A).
–1 Pry out the cap (B), and remove the screw.
–2 Slide the trim upward along the front pillar to
remove it.
–3 Remove the remaining clips from the body.
6. Open the passenger’s door, and remove the
dashboard side cover (A).
–1 Remove the screw.
–2 Gently pull out along the rear edge to release
the clips (B, C).
–3 Gently pull out on the side cover to release the
clips (B) and the tabs (D), then remove the side
cover.
7. From under the passenger’s dash, remove the bolt,
and pull out the fuse/relay box (A).
(cont’d)
03/07/29 10:01:53 61S0X050_200_0075
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст