Honda Odyssey 2004. Manual — part 247
11
12
13
14
14-382
Automatic Transmission
Transmission Installation (cont’d)
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
C
A
B
B
6 x 1.0 mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
C
A
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
B
10 x 1.25 mm
58 N·m (5.9 kgf·m,
43 lbf·ft)
B
10 x 1.25 mm
39 N·m (4.0 kgf·m,
29 lbf·ft)
10 x 1.25 mm
59 N·m (6.0 kgf·m,
43 lbf·ft)
B
10 x 1.25 mm
58 N·m (5.9 kgf·m, 43 lbf·ft)
C
A
10 x 1.25 mm
59 N·m (6.0 kgf·m,
43 lbf·ft)
18. Install the transmission lower mount nuts.
19. Install the power steering fluid line (A) on the
clamps (B), and install the power steering fluid line
bracket (C).
20. Install the rear mount mounting bolts (A).
21. Install the steering gearbox mounting bolts (B) and
the stiffener (C).
22. Install the stiffener (A) and the steering gearbox
mounting bolt (B) with nut (C).
03/07/29 09:40:33 61S0X050_140_0385
15
06
16
*01
−
−
−
14-383
C
D
B
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
A
10 x 1.25 mm
39 N·m (4.0 kgf·m,
29 lbf·ft)
A
B
C
F
E
G
D
6 x 1.0 mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
8 x 1.25 mm
22 N·m (2.2 kgf·m,
16 lbf·ft)
6 x 1.0 mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
C
B
12 x 1.25 mm
59
69 N·m (6.0
7.0 kgf·m,
43
51 lbf·ft)
F
G
E
D
12 x 1.25 mm
78 N·m (7.0 kgf·m,
51 lbf·ft)
A
C
D
A
E
C
D
B
E
10 x 1.25 mm
54 N·m (5.5 kgf·m,
40 lbf·ft)
10 x 1.25 mm
33 N·m (3.4 kgf·m,
25 lbf·ft)
23. Install the steering gearbox mounting bolt (A) and
the power steering fluid line bracket bolts (B).
24. Install the power steering fluid return hose clamp
(C) on the bracket (D).
25. Install the control lever (A) with the shift cable (B)
on the control shaft (C). Do not bend the shift cable
excessively.
26. Install the lock bolt (D) with a new lock washer (E),
then bend the lock washer tab against the bolt.
27. Install the shift cable cover (F), then install the shift
cable holder (G) on the shift cable cover.
NOTE: To prevent damage to the control lever joint,
be sure to install the shift cable holder after
installing the shift cable cover to the torque
converter housing.
28. Install the ball joints on each lower arms (A) with
the castle nuts (hex nuts) (B) and spring pins (C).
29. Install the nut (D) to the ball joint pin (E) on the
stabilizer link (F), then use a 6 mm Allen wrench (G),
and tighten the nut to the specified torque.
30. Install the exhaust pipe A and the three way
catalytic converter (B) assembly.
31. Connect the oxygen sensor connectors (C), then
install them on their connector brackets (D).
Install the harnesses on the clamps (E).
(cont’d)
Replace.
Replace.
03/07/29 09:40:35 61S0X050_140_0386
18
19
*02
*03
14-384
Automatic Transmission
Transmission Installation (cont’d)
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
C
B
A
12 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
B
C
32. Install the splash shield.
33. Install the transmission housing mounting bolts.
34. Install and tighten the nut (A) on the front mount (B),
and install the ground cable (C) to the engine.
35. Remove the engine support hanger.
36. Connect the Primary HO2S connector (A), install it
on its connector bracket (B), and clamp the harness
in the clamp (C).
03/07/29 09:40:36 61S0X050_140_0387
05
06
07
08
14-385
A
B
C
D
F
E
G
B
6 x 1.0 mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
A
B
A
B
E
F
E
D
C
D
C
E
D
B
F
C
A
G
F
37. Install the harness cover (A) on bracket (B).
38. Connect the transmission range switch connector
(C), then install it on its connector bracket (D).
Install the harness clamp (E) on the bracket (F).
39. Connect the output shaft (countershaft) speed
sensor connector (G).
40. Connect the connectors to the torque converter
solenoid valve (A) and the shift solenoid valve B.
41. Connect the connectors to the A/T clutch pressure
control solenoid valves A and B, then install the
harness clamps (C) on the brackets (D).
42. Connect the 8P connector (E), then install it on its
connector bracket (F).
43. Connect the connectors to the shift solenoid valves
A and C, A/T clutch pressure control solenoid valve
C (B), 4th clutch transmission fluid pressure switch
(D), and input shaft (mainshaft) speed sensor (E),
then install the harness clamps (F) on the brackets
(G).
(cont’d)
03/07/29 09:40:37 61S0X050_140_0388
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст