Honda Odyssey 2004. Manual — part 248
*04
09
10
14-386
Automatic Transmission
Transmission Installation (cont’d)
B
A
B
D
C
12 x 1.25 mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
9 N·m
(0.9 kgf·m, 6.5 lbf·ft)
B
A
A
D
C
A
B
C
44. Install the starter (A) on the torque converter
housing. Connect the starter cables (B) to the
starter, and install the harness clamp (C) on the
clamp bracket (D). Make sure the crimped side of
the starter cable ring terminal is facing out.
45. Connect the ATF cooler hoses (A) to the ATF cooler
lines (B) (see page 14-389). Clamp the ATF cooler
hose with the clamp (C) on the starter by aligning
the white dot (D) on the hose with the clamp.
46. Install the transmission breather tube (A) in the
clamp (B) by aligning the dot (C) with the clamp.
47. Install the battery base bracket and battery base.
48. Install the battery cable clamps, connector, and
relay bracket on the battery base.
49. Install the battery tray and battery, then secure the
battery with its hold-down bracket.
50. Install the intake air duct, resonator cover, and air
cleaner housing assembly.
03/07/29 09:40:38 61S0X050_140_0389
*05
*06
14-387
12 x 1.25 mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
51. Install the engine covers.
52. Refill the transmission with ATF (see step 5 on page
14-368).
53. Connect the battery positive terminal, then connect
the negative terminal.
54. Set the parking brake. Start the engine, and shift
the transmission through all gears three times.
55. Check the shift lever operation, A/T gear position
indicator operation, and shift cable adjustment.
56. Check and adjust the front wheel alignment (see
page 18-5).
57. Reinstall the support rod of the hood to the proper
location, and secure the windshield washer
reservoir opening with the bolt.
58. Start the engine, and let it reach normal operating
temperature (the radiator fan comes on) with the
transmission in the P or N position, then turn it off
and check the ATF level (see page 14-367).
59. Do the PCM idle learn procedure (see page 11-202).
60. Do the power window control unit reset procedure
(2003-2004 model) (see page 22-200).
61. Perform a road test (see page 14-352).
62. Enter the anti-theft code for the radio and the
navigation system, then enter the radio station
presets, and set the clock.
63. Loosen the front mount nut after the road test, then
retighten the nut to the specified torque.
03/07/29 09:40:38 61S0X050_140_0390
−
−
−
−
01
*01
S0X4AA1E10400013011LBAT00
Special Tools Required
Air Pressure: MAX 845 kPa (8.45 kgf/cm , 120 psi)
2
14-388
Automatic Transmission
ATF Cooler Flushing
A
B
C
D
A
Commercially Available Transmission Cooler Flusher
Kent-Moore J38405-A or equivalent
This procedure should be performed before reinstalling
the transmission.
1. Check the equipment for wear and cracks before
using it. Replace any worn or cracked components.
2. Using the measuring cup, fill the flusher (A) with 21
ounces (approximately 2/3 full) of biodegradable
flushing fluid (J35944-20). Do not substitute with
any other fluid. Follow the handling procedure on
the fluid container.
3. Secure the flusher filler cap, and pressurize the
flusher with compressed air to 550
829 kpa (5.6
8.45 kgf/cm , 80
120 psi). The air line should be
equipped with a water trap to ensure a dry air
system.
4. Hang the flusher under the vehicle.
5. Attach the flusher discharge hose (B) to the return
line of the ATF cooler using a clamp.
6. Connect the drain hose (C) to the inlet line on the
ATF cooler using a clamp. Securely clamp the
opposite end of the drain hose to a bucket (D) or
floor drain.
7. With the water and air valves (A) off, attach the
water and air supplies to the flusher. (Hot water if
available.)
8. Turn on the water valve for 10 seconds. If water
does not flow through the cooler, it is completely
plugged, cannot be flushed, and must be replaced.
9. Press the trigger to mix the flushing fluid into the
water flow. Use the wire clip to hold the trigger
down.
10. While flushing with the water and flushing fluid for
2 minutes, turn the air valve on for 5 seconds every
15
20 seconds to create a surging action.
11. Turn the water valve off. Release the trigger, then
reverse the hoses to the cooler so you can flush in
the opposite direction. Repeat steps 8 through 10.
12. Release the trigger, and rinse the cooler with water
for 1 minute.
13. Turn the water valve and the water supply off.
14. Turn the air valve on for 2 minutes, or until no
moisture is visible leaving the drain hose. Residual
moisture in the cooler or lines can damage the
transmission.
15. Remove the flusher from the cooler line. Attach the
drain hose to an ATF container.
16. Install the transmission, and leave the drain hose
attached to the cooler line.
2
03/07/29 09:40:39 61S0X050_140_0391
01
S0X4AA1E10400013012KBAT00
−
−
−
−
14-389
14-389
ATF Cooler Hose Replacement
A
D
E
B
6
8 mm
(0.2
0.3 in.)
C
A
C
2
4 mm
(0.1
0.2 in.)
17. Make sure the transmission is in the P position.
Fill the transmission with ATF, and run the engine
for 30 seconds or until approximately 0.95
(1.0
US qt) is discharged.
18. Remove the drain hose, and reconnect the cooler
return hose to the transmission.
19. Refill the transmission with ATF to the proper level
(see step 5 on page 14-367).
1. Connect the cooler hoses (A) to the lines (B) and the
ATF cooler, and secure them with the clips (C).
2. Clamp the ATF cooler hose with the yellow mark
(D) on the clamp (E).
03/07/29 09:40:40 61S0X050_140_0392
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст