Honda Odyssey 2004. Manual — part 548
![](/vehicles/vescileif/vis/udared/buyry.png)
−
−
−
−
−
−
01
*01
S0X4AZ3K79100081043FAAT00
’02 Model
DTC 4-3:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-134
SRS
DTC Troubleshooting (cont’d)
A
07TAZ-SZ5011A
07SAZ-TB4011A
C581
07TAZ-SZ5011A
07SAZ-TB4011A
A
Short to Another Wire or Decreased
Resistance in Front Passenger’s Seat Belt
Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the right side wire
harness 2P connector (A).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short in the front passenger’s seat belt
tensioner; replace the front passenger’s seat belt
(see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the SRS main wire harness 2P
connector C581 from the right side wire harness 2P
connector (A).
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short in the right side wire harness; replace
the right side wire harness.
15. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Does the SRS indicator stay on?
Is DT C 4-3 indicated?
Is DT C 4-3 indicated?
03/07/29 10:34:48 61S0X050_230_0134
![](/vehicles/vescileif/vis/udared/yenok.png)
−
−
03
04
05
YES
NO
23-135
A
B
C
A
SRS UNIT CONNECTOR A (18P)
16. Disconnect the driver’s airbag connector (A), front
passenger’s airbag connector (B), and driver’s seat
belt tensioner connector (C).
17. Disconnect SRS unit connector A (18P) from the
SRS unit.
18. Disconnect the special tool from the SRS main
harness 2P connector.
19. Check resistance between the No. 9 terminal and
the No. 18 terminals of SRS unit connector A (18P).
There should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 20.
(cont’d)
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:34:49 61S0X050_230_0135
![](/vehicles/vescileif/vis/udared/wareello.png)
−
−
*02
07
YES
NO
23-136
SRS
DTC Troubleshooting (cont’d)
C851
A
SRS MAIN HARNESS 28P CONNECTOR
20. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
21. Check resistance between the No. 6 and the No. 15
terminals of the SRS main harness 28P connector.
There should be an open circuit, or at least 1 M
.
Short in the SRS floor harness; replace the
SRS floor harness.
Short in the SRS main harness; replace the
SRS main harness.
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:34:49 61S0X050_230_0136
![](/vehicles/vescileif/vis/udared/erzmy.png)
−
−
−
−
−
−
01
02
S0X4AZ3K79100081044FAAT00
’02 Model
DTC 4-4:
Special Tools Required
YES
NO
YES
NO
YES
NO
23-137
A
07TAZ-SZ5011A
07SAZ-TB4011A
07TAZ-SZ5011A
07SAZ-TB4011A
Short to Power in Front Passenger’s
Seat Belt Tensioner
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead C 07TAZ-SZ5011A
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the front passenger’s seat belt
tensioner 2P connector from the right side wire
harness 2P connector (A).
5. Connect the special tool (2
connector) to the
right side wire harness 2P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the front passenger’s seat
belt tensioner; replace the front passenger’s seat
belt (see page 23-4).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10.
11. Connect the special tool (2
connector) to the SRS
main harness 2P connector.
12. Reconnect the battery negative cable.
13. Erase the DTC memory.
14. Read the DTC.
Go to step 15.
Short to power in the right side wire harness;
replace the right side wire harness.
(cont’d)
Does the SRS indicator stay on?
Is DT C 4-4 indicated?
Is DT C 4-4 indicated?
03/07/29 10:34:50 61S0X050_230_0137
Disconnect the SRS main harness 2P connector C581
from the right side wire harness 2P connector (A).
A
C581
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст