Honda Odyssey 2004. Manual — part 114
−
−
−
−
−
−
−
02
01
S0X4AZ1K77100091297FAAT00
YES
NO
YES
NO
YES
NO
DTC P1297
’01 Model:
11-154
11-154
PGM-FI System
DTC Troubleshooting (cont’d)
PCM CONNECTOR A (32P)
ELD (GRN/RED)
ELD 3P CONNECTOR
ELD (GRN/RED)
8. Turn the ignition switch OFF.
9. Disconnect PCM connector A (32P).
10. Check for continuity between body ground and
PCM connector terminal A30.
Repair short in the wire between the PCM
(A30) and the ELD.
Substitute a known-good PCM and recheck
(see page 11-5). If the symptom/indication goes
away, replace the original PCM.
1. Reset the PCM (see page 11-4).
2. Start the engine.
3. Turn on the headlights.
Go to step 4.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the ELD and the PCM.
4. Turn the ignition switch and the headlights OFF.
5. Disconnect the ELD 3P connector.
6. Turn the ignition switch ON (II).
7. Measure voltage between body ground and ELD 3P
connector terminal No. 3.
Replace the ELD.
Go to step 8.
ELD Circuit Low
Voltage
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Is DT C P1297 indicated?
Is ther e about 5 V ?
03/07/29 09:22:46 61S0X050_110_0154
−
−
−
−
−
−
−
02
*01
S0X4AZ6K77100091298FAAT00
YES
NO
YES
NO
YES
NO
DTC P1298
’99-00, ’02-04 Models:
11-155
11-155
PCM CONNECTOR E (31P)
ELD (GRN/RED)
ELD 3P CONNECTOR
IG1 (BLK/YEL)
8. Turn the ignition switch OFF.
9. Disconnect PCM connector E (31P).
10. Check for continuity between body ground and
PCM connector terminal E19.
Repair short in the wire between the PCM
(E19) and the ELD.
Substitute a known-good PCM and recheck
(see page 11-5). If the symptom/indication goes
away, replace the original PCM.
1. Reset the PCM (see page 11-4).
2. Start the engine.
3. Turn on the headlights.
Go to step 4.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the ELD and the PCM.
4. Turn the ignition switch and headlights OFF.
5. Disconnect the ELD 3P connector.
6. Turn the ignition switch ON (II).
7. Measure voltage between body ground and ELD 3P
connector terminal No. 1.
Go to step 8.
Check the No. 6 ECU (PCM) CRUISE
CONTROL (15A) fuse in the driver’s under-dash
fuse/relay box. If the fuse is OK, repair open in the
wire between the No. 6 ECU (PCM) CRUISE
CONTROL (15A) fuse and the ELD.
8. Turn the ignition switch OFF.
(cont’d)
ELD
Circuit High Voltage
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Is DT C P1298 indicated?
Is ther e batter y voltage?
03/07/29 09:22:46 61S0X050_110_0155
−
−
−
−
−
−
01
02
*02
03
YES
NO
YES
NO
YES
NO
11-156
PGM-FI System
DTC Troubleshooting (cont’d)
ELD 3P CONNECTOR
JUMPER WIRE
ELD
(GRN/RED)
PCM CONNECTOR A (32P)
ELD (GRN/RED)
ELD 3P CONNECTOR
GND
(BLK)
B (25P)
LG1 (BRN/BLK)
A (32P)
PCM CONNECTORS
ELD (GRN/RED)
9. Connect ELD 3P connector terminal No. 3 to body
ground with a jumper wire.
10. Disconnect PCM connector A (32P).
11. Check for continuity between body ground and
PCM connector terminal A30.
Go to step 12.
Repair open in the wire between the PCM
(A30) and the ELD.
12. Check for continuity between ELD 3P connector
terminal No. 2 and body ground.
Reconnect the ELD 3P connector and PCM
connector A (31P). Go to step 13.
Repair open in the wire between the ELD and
G201.
13. Start the engine, and let it to idle.
14. While measuring voltage between PCM connector
terminals A30 and B20, turn the headlights on (low).
Substitute a known-good PCM and recheck
(see page 11-5). If the symptom/indication goes
away, replace the original PCM.
Replace ELD.
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is ther e continuity?
Is ther e continuity?
Does the voltage dr op?
03/07/29 09:22:47 61S0X050_110_0156
−
−
−
−
−
−
−
*01
01
02
S0X4AZ1K77100091298FAAT00
DTC P1298
’01 Model:
YES
NO
YES
NO
YES
NO
11-157
ELD 3P CONNECTOR
IG1 (BLK/YEL)
ELD 3P CONNECTOR
ELD
(GRN/RED)
JUMPER WIRE
PCM CONNECTOR E (31P)
ELD (GRN/RED)
ELD Circuit High
Voltage
1. Reset the PCM (see page 11-4).
2. Start the engine.
3. Turn on the headlights.
Go to step 4.
Intermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the ELD and the PCM.
4. Turn the ignition switch and headlights OFF.
5. Disconnect the ELD 3P connector.
6. Turn the ignition switch ON (II).
7. Measure voltage between body ground and ELD 3P
connector terminal No. 1.
Go to step 8.
Check the No. 6 ECU (PCM) CRUISE
CONTROL (15A) fuse in the driver’s under-dash
fuse/relay box. If the fuse is OK, repair open in the
wire between the No. 6 ECU (PCM) CRUISE
CONTROL (15A) fuse and the ELD.
8. Turn the ignition switch OFF.
9. Connect ELD 3P connector terminal No. 3 to body
ground with a jumper wire.
10. Disconnect PCM connector A (32P).
11. Check for continuity between body ground and
PCM connector terminal E19.
Go to step 12.
Repair open in the wire between the PCM
(E19) and the ELD.
(cont’d)
Wire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is DT C P1298 indicated?
Is ther e batter y voltage?
Is ther e continuity?
03/07/29 09:22:48 61S0X050_110_0157
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст