Honda Odyssey 2004. Manual — part 199
−
−
*04
*01
*02
S0X4AA0E10410445001MCAT00
Standard:
84.6
85.6 mm (3.33
3.37 in.)
PARK LEVER STOP
Mark
Part Number
L1
L2
14-190
14-190
Transmission End Cover
End Cover and Idler Gear Removal
(cont’d)
Park Lever Stop Inspection and
Adjustment
C
D
F
B
A
E
C
E
A
D
6 x 1.0 mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
B
L1
L2
E
9. Remove the mainshaft idler gear (A) and the
secondary shaft idler gear (B) with a puller (C).
10. Remove the bearing hub (D) with the puller from
the countershaft, then remove the countershaft
idler gear (E) and bearings.
11. Remove the park gear (F) with the puller.
12. Remove the park pawl, spring, shaft, and shaft stop.
13. Remove the park lever from the control shaft.
14. Remove the line bolts, then remove the ATF cooler
lines.
1. Set the park lever (A) in the P position.
2. Measure the distance (B) between the park pawl
shaft (C) and the park lever roller pin (D).
3. If the measurement is out of tolerance, select and
install the appropriate park lever stop (E) from the
table.
1
24537-PA9-003
11.00 mm
(0.433 in.)
11.00 mm
(0.433 in.)
2
24538-PA9-003
10.80 mm
(0.425 in.)
10.65 mm
(0.419 in.)
3
24539-PA9-003
10.60 mm
(0.417 in.)
10.30 mm
(0.406 in.)
4. After replacing the park lever stop, make sure the
distance is within tolerance.
03/07/29 09:34:19 61S0X050_140_0193
*03
S0X4AA0E10410459801KAAT00
Exploded View
14-191
Transmission Housing
Housing and Shaft Assembly Removal
TRANSMISSION HOUSING
MOUNTING BOLTS
HARNESS CLAMP BRACKET
TRANSMISSION HANGER/
HARNESS CLAMP BRACKET
TRANSMISSION HOUSING
TRANSMISSION HANGER
REVERSE IDLER
GEAR
MAINSHAFT
SUBASSEMBLY
TORQUE CONVERTER HOUSING
DIFFERENTIAL ASSEMBLY
COUNTERSHAFT
SUBASSEMBLY
SECONDARY SHAFT
SUBASSEMBLY
COUNTERSHAFT
4TH GEAR
REVERSE SELECTOR
HUB
REVERSE SELECTOR
SHIFT FORK
COUNTERSHAFT
REVERSE GEAR
COUNTERSHAFT
2ND GEAR
REVERSE IDLER GEAR SHAFT
REVERSE IDLER GEAR
SHAFT HOLDER
LOCK WASHER
TRANSMISSION HOUSING
GASKET
(cont’d)
Replace.
Replace.
03/07/29 09:34:20 61S0X050_140_0194
*01
*02
01
Special Tools Required
14-192
Transmission Housing
Housing and Shaft Assembly Removal (cont’d)
A
B
C
A
A
B
C
07HAC-PK40102
D
Housing puller 07HAC-PK40102
NOTE: Refer to the exploded view as needed during the
following procedure.
1. Remove the two bolts securing the reverse idler
gear shaft holder, then remove the reverse idler
gear shaft holder (A), shaft (B), and washer (C).
2. Remove the transmission housing mounting bolts,
transmission hangers, and harness clamp bracket.
3. Move the reverse idler gear (A) to disengage it from
the mainshaft and countershaft reverse gears.
NOTE: The transmission housing will not separate
from the torque converter housing if the reverse
idler gear is not moved.
4. Align the spring pin (A) on the control shaft (B) with
the transmission housing groove (C) by turning the
control shaft.
5. Install the special tool over the mainshaft, then
remove the transmission housing (D).
NOTE: If the top arm of your housing puller is too
short, replace it with Housing Puller Arm, 205 mm
07SAC-P0Z0101.
6. Remove the reverse idler gear, needle bearings,
and thrust washer from the transmission housing.
7. Remove the countershaft 2nd gear, then remove
the countershaft reverse gear and the needle
bearing.
8. Remove the lock bolt securing the shift fork, then
remove the shift fork with the reverse selector,
reverse selector hub, and countershaft 4th gear. If
the reverse selector hub is press-fitted, leave it and
4th gear on the countershaft.
9. Remove the secondary shaft subassembly.
If the reverse selector hub is press-fitted, remove
the secondary shaft subassembly, countershaft
subassembly and mainshaft subassembly together.
10. Remove the countershaft subassembly.
11. Remove the mainshaft subassembly.
12. Remove the differential assembly.
03/07/29 09:34:21 61S0X050_140_0195
01
02
03
S0X4AA0E10410917423KDAT00
−
−
Special Tools Required
14-193
Bearing Removal and Installation
A
C
B
C
A
B
A
B : 0
7 mm
(0
0.28 in.)
• Driver 07749-0010000
• Seal driver attachment
07GAD-PG40101 or 07GAD-PG40100
• Attachment, 62 x 68 mm 07746-0010500
• Attachment, 72 x 75 mm 07746-0010600
NOTE: Coat all parts with ATF before assembly.
1. To remove the mainshaft bearing (A), countershaft
bearing (B), and secondary shaft bearing (C) from
the transmission housing, expand each snap ring
with the snap ring pliers, then push the bearing out.
NOTE: Do not remove the snap rings unless it’s
necessary to clean the grooves in the housing.
2. Install the bearings in the direction shown.
3. Expand each snap ring with the snap ring pliers,
and insert the bearing part-way into the housing.
4. Release the pliers, then push the bearing down into
the housing until the snap ring snaps in place
around it.
5. After installing the bearings verify the following:
• The snap rings (A) are seated in the bearing and
housing grooves.
• The ring end gaps (B) are correct.
03/07/29 09:34:22 61S0X050_140_0196
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст