Honda Odyssey 2004. Manual — part 192
01
01
03
S0X4AA0E10411412281MBAT00
14-162
Automatic Transmission
Shift Cable Adjustment
D
B
A
G
E
C
F
A
B
C
SRS components are located in this area. Review the
SRS component locations (see page 23-18), and the
precautions and procedures (see page 23-21) in the SRS
before performing repairs or service.
1. Remove the steering column covers (see page 17-
25).
2. Shift the transmission into the N position.
3. Remove the nut (A) securing the shift cable end (B),
then separate the shift cable (C) from the shift lever
assembly (D).
4. Rotate the socket holder (E) on the shift cable
counterclockwise a quarter turn, then slide the
holder to remove the shift cable from the shift cable
bracket (F).
NOTE: Do not remove the shift cable by twisting
the shift cable guide (G).
5. Push the shift cable until it stops, then release it.
Pull the shift cable back two steps so that the shift
lever position is in the N.
6. Turn the ignition switch ON (II), and verify that the
N position indicator comes on.
7. Turn the ignition switch OFF.
8. Insert a 6.0 mm (0.24 in.) pin (A) through the
positioning hole (B) on the detent plate and into the
positioning hole (C) on the control bracket.
03/07/29 09:33:58 61S0X050_140_0165
02
04
03
14-163
E
D
G
F
H
A
B
C
Properly Installed:
Improperly Installed:
A
B
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
9. Align the socket holder (A) on the shift cable (B)
with the slot in the shift cable bracket (C), then slide
the holder into the bracket. Install the shift cable
end (D) over the mounting stud (E) by aligning its
square hole (F) with the square fitting (G) at the
bottom of the stud, and rotate the holder clockwise
a quarter turn to secure the shift cable.
NOTE: Do not install the shift cable by twisting the
shift cable guide (H).
10. Verify that the shift cable end (A) is properly
installed on the mounting stud (B).
11. If improperly installed, remove the shift cable from
the shift cable bracket, and reinstalled the shift
cable. Do not install the shift cable end on the
mounting stud while the shift cable is on the shift
cable bracket.
12. Install and tighten the nut to the specified torque.
13. Remove the 6.0 mm (0.24 in.) pin that was installed
to hold the shift lever.
14. Move the shift lever to each gear, and verify that
the A/T gear position indicator follows the
transmission range switch.
15. Push the shift lock release, and verify that the shift
lever releases.
Cable end rides on the bottom
of the mounting stud.
03/07/29 09:33:58 61S0X050_140_0166
*01
*02
S0X4AA0E10410700000DAAT00
14-164
A/T Gear Position Indicator
Component Location Index
A/T GEAR POSITION INDICATOR
POWERTRAIN CONTROL MODULE (PCM)
TRANSMISSION RANGE SWITCH
D4 Indicator Cicuit Troubleshooting
1999-2000 models, page 14-166
2001 model, page 14-169
Indicator Input Test, page 14-172
Test, page 14-173
Replacement, page 14-174
03/07/29 09:34:00 61S0X050_140_0167
Indicator Bulb Replacement, page 14-176
*01
S0X4AA0E10410700000EAAT00
−
−
−
−
14-165
Circuit Diagram
RELAY
C22
C20
C12
C4
C13
B14/
D9/
D15/
D14/
D8/
WHT
YEL
YEL
YEL
CIRCUIT
SPEEDOMETER
WHT
BOX
DRIVER’S
FUSE/RELAY BOX
(DRIVER’S)
UNIT
CONTROL
MULTIPLEX
UNDER DASH
FUSE/RELAY
CUT
STARTER
BLU/WHT
NP
ATP
BRN
BLU
PNK
RED/BLK
WHT
RED/BLK
PNK
BLU
BRN
BLU/WHT
VSS
A9/E26
OUT
LT BLU
E
ST
A
No.9 (10A)
IG1
BAT
CONTROL
BLK
G503
YEL
IND
R
1
2
UNIT
CRUISE
BLK
G101
RED/WHT
PNK
GRY
BLK/BLU
WHT
RED
YEL
GRN
BLU
BRN
BRN
BLU
PNK
RED/BLK
WHT
BLK/BLU
GRN/BLK
BRN
BLU
PNK
YEL
WHT
POWERTRAIN CONTROL MODULE (PCM)
DRIVER’S
UNDER DASH
IGNITION
SWITCH
No.41 (120A)
D
D3
D4
ATP
1
ATP
D
2
UNDER HOOD FUSE/RELAY BOX
D6/C21
A14/E5
ATP
ATP
ATP
D4
TRANSMISSION RANGE SWITCH
1
2
N
R
P
D
D
N
R
BATTERY
GAUGE ASSEMBLY
P
CIRCUIT
DIMMING
No.42 (50A)
C17
B2
P
3
2
1
4
5
6
7
8
9
10
C5
B11
B16
C7
C6
C16
C4
C15
C12
4
3
3
4
PCM terminal number shows the number of the 1999
2000 models/2001 models.
NOTE:
03/07/29 09:34:01 61S0X050_140_0168
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст