Honda Odyssey 2004. Manual — part 540
−
−
−
−
01
02
S0X4AZ3K79100081013FAAT00
’02 Model
DTC 1-3:
Special Tools Required
YES
NO
YES
NO
23-102
SRS
DTC Troubleshooting (cont’d)
A
07XAZ-SZ30100
07SAZ-TB4011A
B
A
Short to Another Wire or Decreased
Resistance in Driver’s Airbag Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel 4P connector (A).
5. Connect the special tool (2
connectors) to the
cable reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short in the driver’s airbag inflator; replace
the driver’s airbag (see page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger’s airbag 4P
connector (A) from the SRS main harness 4P
connector (B).
Does the SRS indicator stay on?
Is DT C 1-3 indicated?
03/07/29 10:34:25 61S0X050_230_0102
−
−
−
−
03
04
05
YES
NO
YES
NO
23-103
A
B
A
SRS UNIT CONNECTOR A (18P)
11. Disconnect both seat belt tensioner 2P connectors
(A) from the side wire harness 2P connectors (B).
12. Disconnect SRS unit connector A (18P) from the
SRS unit.
13. Disconnect the special tool from the cable reel 4P
connector.
14. Check resistance between the No. 7 and the No. 16
terminals and between the No. 6 and the No. 15
terminals of SRS unit connector A (18P). There
should be an open circuit, or at least 1 M
.
Faulty SRS unit; replace the SRS unit (see
page 23-382).
Go to step 15.
15. Disconnect the cable reel from the dashboard wire
harness. Check resistance between the No. 7 and
the No. 16 terminals and between the No. 6 and the
No. 15 terminals of SRS unit connector A (18P).
There should be an open circuit, or at least 1 M
.
Replace the cable reel (see page 23-377).
Go to step 16.
(cont’d)
Wire side of female terminals
Is the r esistance as specif ied?
Is the r esistance as specif ied?
03/07/29 10:34:26 61S0X050_230_0103
−
−
*01
07
YES
NO
23-104
SRS
DTC Troubleshooting (cont’d)
C851
A
SRS MAIN HARNESS 28P CONNECTOR
16. Disconnect the SRS main harness 28P connector
(A) from the SRS floor harness 28P connector C851.
17. Check resistance between the No. 9 and the No. 10
terminals and between the No. 3 and the No. 4
terminals of the SRS main harness 28P connector.
There should be an open circuit, or at least 1 M
.
Replace the SRS floor harness.
Replace the SRS main harness.
Wire side of female terminals
Is the r esistance as specif ied?
03/07/29 10:34:27 61S0X050_230_0104
−
−
−
−
01
02
03
S0X4AZ3K79100081014FAAT00
’02 Model
DTC 1-4:
Special Tools Required
YES
NO
YES
NO
23-105
A
07XAZ-SZ30100
07SAZ-TB4011A
B
A
A
B
Short to Power in Driver’s Airbag
Inflator
• SRS inflator simulator 07SAZ-TB4011A
• SRS simulator lead F 07XAZ-SZ30100
1. Erase the DTC memory (see page 23-38).
2. Turn the ignition switch ON (II), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Go to step 3.
Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-39).
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the driver’s airbag 4P connector from
the cable reel 4P connector (A).
5. Connect the special tool (2
connectors) to the
cable reel 4P connector.
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC (see page 23-35).
Go to step 9.
Short to power in the driver’s airbag inflator;
replace the driver’s airbag (see page 23-368).
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger’s airbag 4P
connector (A) from the SRS main harness 4P
connector (B).
11. Disconnect both seat belt tensioner 2P connectors
(A) from the side wire harness 2P connectors (B).
(cont’d)
Does the SRS indicator stay on?
Is DT C 1-4 indicated?
03/07/29 10:34:27 61S0X050_230_0105
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст