Honda Odyssey 2004. Manual — part 365
01
02
S0X4A00J46127053501KBAT00
Seat-back Cover
20-102
Seats
Front Seat Cover Replacement
E
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
A
D
B
C
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
E
10 x 1.25 mm
38 N·m (3.9 kgf·m,
28 lbf·ft)
6 x 1.0 mm
9.8 N·m (1.0 kgf·m,
7.2 lbf·ft)
A
B, C
B, C
Fastener Locations
B
: Screw, 2
C
: Screw, 2
• For ’02-04 models: SRS components are located in
this area. Review the SRS component locations,
’02 model (see page 23-19), ’03-04 models (see page
23-20), and the precautions and procedures (see page
23-21) before performing repairs or service.
• For ’03-04 models: The operation of the driver’s seat
position sensor must be checked after any of these
– Driver’s seat position sensor replacement
– Cover plate (front side of driver’s seat slide rail)
replacement
• For ’03-04 models: The front passenger’s weight
sensor (SWS) unit must be calibrated after any of the
– Front passenger’s seat replacement (including any
seat components)
– Replacement of the seat weight sensors
– Replacement of the seat weight sensor unit
NOTE:
• With side airbag (’02-04 models): Seats with a side
airbag have a ‘‘Side Airbag’’ label on the seat-back.
Because the component parts (seat-back cover,
cushion, etc.) of seats with and without airbags are
different, make sure you install only the correct
replacement parts.
• With side airbag (’02-04 models): Do not repair any
tears or frayed spots of the seat-back cover. If
necessary, replace the seat-back cover.
• Take care not to tear the seams or damage the seat
covers.
• With side airbag (’02-04 models): Do not touch the
OPDS sensor in the seat-back pad. Keep the sensor
free from grease, oils and moisture, as they can
damage the sensor. Oils can corrode the sensor, and
cause it to malfunction.
• Put on gloves to protect your hands.
1. Release the zipper (A) and pull back the armrest
cover (B). Remove the armrest center pin (C),
armrest (D), and armrest pins (E).
2. Pry off the caps (A) and remove the screws (B or C)
using a Torx T30 bit. Then remove the grab handle.
03/07/29 10:03:14 61S0X050_200_0104
these actions (see page 23-42):
actions (see page 23-47):
01
03
02
03
20-103
A
B
B
A
B
A
A
B
A
B
A
A
3. If equipped, remove the clip (A), then remove the
lumbar support knob (B).
4. Fold the seat-back forward.
5. For ’99-01 models: Release the hook (A), and fold
back the edge of the seat-back cover (B) all the way
around.
6. For ’02-04 models: Release the hook (A), and unzip
the seat-back cover (B), then fold it back.
7. For ’02-04 models: On the passenger’s seat, release
all of the inside springs (A).
(cont’d)
03/07/29 10:03:15 61S0X050_200_0105
04
05
06
07
’99-01 models
’02-04 models (driver’s)
’02-04 models (passenger’s)
20-104
Seats
Front Seat Cover Replacement (cont’d)
A
B
C
A
B
A
B
B
A
A
B
8. For some ’02-04 models: If equipped with side
airbag, release the hooks (A) of the reinforcing
cloth (B) from the seat-back frame (C).
9. Fold back the edge of the seat-back cover (A) all the
way around, then release the clips (A).
03/07/29 10:03:16 61S0X050_200_0106
05
06
07
20-105
A
B
C
A
B
C
D
A
B
10. For ’99-01 models: Release all the clips (A)
fastening the seat-back cover (B) and frame wire (C).
11. Lift and pull out the release button (A), and remove
the screw (B), then remove the headrest guide (C).
12. Remove the seat back cover (D).
13. Install the cover in the reverse order of removal,
and note these items:
• To prevent wrinkles when installing a seat-back
cover, make sure the material is stretched evenly
over the pad before securing the hook, clips and
inside springs.
• Replace any clips (A) you removed with new
ones using commercially available upholstery
ring pliers (B).
• With side airbag (’02-04 models): Use only
original Honda replacement seat-back covers.
(cont’d)
03/07/29 10:03:17 61S0X050_200_0107
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст