Honda Passport (2022 year). Manual in english — page 28
445
uu
Honda Sensing
®
u
Collision Mitigation Braking System
TM
(CMBS
TM
)
Driving
■
Speed bumps, road work sites, train tracks, roadside objects, etc.
You drive over speed bumps, steel road plates, etc., or your vehicle approaches train
tracks or roadside objects [such as a traffic sign and guard rail] on a curve or, when
parking, stationary vehicles and walls.
446
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Driving
Adaptive Cruise Control (ACC)
Helps maintain a constant vehicle speed and a set following-interval behind a vehicle
detected ahead of yours, without you having to keep your foot on the brake or the
accelerator.
1
ACC cannot be activated if Intelligent Traction
Management setting is
Snow
,
Sand
*
or
Mud
*
.
3
WARNING
Improper use of ACC can lead to a crash.
Use ACC only when driving on expressways
or freeways and in good road and weather
conditions.
3
WARNING
ACC has limited braking capability.
When your vehicle speed drops below
22 mph (35 km/h), ACC will automatically
cancel and no longer will apply your
vehicle's brakes.
Always be prepared to apply the brake
pedal when conditions require.
When to use
■
Vehicle speed for adaptive cruise control: Desired speed in a
range above roughly 25 mph (40 km/h)
■
Gear positions for adaptive cruise control: In
(
D
or
(
S
The radar sensor is behind
the emblem.
The camera is located
behind the rearview
mirror.
* Not available on all models
Continued
447
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Driving
■
How to activate the system
1
Important Reminder
As with any system, there are limits to ACC. Use the
brake pedal whenever necessary, and always keep a
safe interval between your vehicle and other vehicles.
You can read about handling information for the
camera equipped with this system.
2
P. 473
The radar sensor for ACC is shared with the Collision
Mitigation Braking System
TM
(CMBS
TM
).
2
Collision Mitigation Braking System
P. 434
How to use
■
Press the
MAIN
button on
the steering wheel.
ACC is on in the driver
information interface.
Adaptive cruise control is
ready to use.
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
448
Driving
Take your foot off the pedal and press the
–/SET
button when you reach the desired
speed. The moment you release the
–/SET
button, the set speed is fixed, and ACC
begins.
When ACC starts operating, the vehicle icon,
distance bars and set speed appear on the
driver information interface.
■
To Set the Vehicle Speed
1
ACC may not work properly under certain conditions.
2
ACC Conditions and Limitations
When not using ACC: Turn off adaptive cruise by
pressing the
MAIN
button. This also will turn off the
Lane Keeping Assist System (LKAS).
When the
MAIN
button is pressed, ACC and Lane
Keeping Assist System (LKAS) are both turned on or
off.
You can switch the displayed set speed
measurements on the driver information interface
between mph and km/h.
2
P. 117
Do not use ACC under the following conditions:
•
On roads with heavy traffic or while driving in
continuous stop and go traffic.
•
On roads with sharp turns.
•
On roads with steep downhill sections, as the set
vehicle speed can be exceeded by coasting. In such
cases, ACC will not apply the brakes to maintain
the set speed.
•
On roads with toll collection facilities or other
objects between lanes of traffic, or in parking
areas, or facilities with drive through access.
On when
adaptive cruise
control begins
Press and release
–/SET
Button
Set Vehicle
Interval
Set Vehicle
Speed
Continued
449
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Driving
■
There is a vehicle ahead
ACC monitors if a vehicle ahead of you enters the ACC range. If a vehicle is detected
doing so, the ACC system maintains or decelerates your vehicle’s set speed in order
to keep the vehicle’s set following-interval from the vehicle ahead.
2
To Set or Change Following-interval
P. 454
When a vehicle whose speed is slower than
your set speed is detected in front of you, your
vehicle starts to slow down.
■
When in Operation
1
If the vehicle detected ahead of you slows down
abruptly, or if another vehicle is detected cutting in
front of you, the beeper sounds and a message
appears on the driver information interface.
Depress the brake pedal, and keep an appropriate
interval from the vehicle ahead.
Beep
ACC Range: 394 ft. (120 m)
A vehicle icon appears on the
driver information interface.
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
450
Driving
■
There is no vehicle ahead
Your vehicle maintains the set speed without
having to keep your foot on the brake or
accelerator pedal.
If there previously was a vehicle detected
ahead that kept your vehicle from traveling at
the set speed, ACC accelerates your vehicle to
the set speed, and then maintains it.
■
When you depress the accelerator pedal
You can temporarily increase the vehicle speed. In this case, there is no audible or
visual alerts even if a vehicle is in ACC range.
ACC stays on unless you cancel it. Once you release the accelerator pedal, the
system resumes the set speed.
1
Even if the interval between your vehicle and the
vehicle detected ahead is short, ACC may start
accelerating your vehicle under the following
circumstances:
•
The vehicle ahead of you is going at almost the
same speed as, or faster than, your vehicle.
•
A vehicle that cuts in front of you is going faster
than your vehicle, gradually increasing the interval
between the vehicles.
You can also set the system to beep when a vehicle in
front of you comes in and goes out of the ACC
detecting range. Change the
ACC Forward Vehicle
Detect Beep
setting.
2
P. 327
Limitations
You may need to use the brake to maintain a safe
interval when using ACC. Additionally, ACC may not
work properly under certain conditions.
2
ACC Conditions and Limitations
P. 451
A vehicle icon with dotted-line
contour appears on the driver
information interface.
Continued
451
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Driving
The system may automatically shut off and the
ACC
indicator will come on under
certain conditions. Some examples of these conditions are listed below. Other
conditions may reduce some of the ACC functions.
2
P. 473
■
Environmental conditions
Driving in bad weather (rain, fog, snow, etc.).
■
Roadway conditions
Driving on a snowy or wet roadway (obscured lane marking, vehicle tracks, reflected
lights, road spray, high contrast).
■
Vehicle conditions
•
The outside of the windshield is blocked by dirt, mud, leaves, wet snow, etc.
•
An abnormal tire or wheel condition (incorrect sizes, varied sizes or construction,
improperly inflated, compact spare tire, etc.).
•
The camera temperature gets too high.
•
The parking brake is applied.
•
When the front grille is dirty.
•
The vehicle is tilted due to a heavy load or suspension modifications.
•
When tire chains are installed.
•
The vehicle is towing a trailer.
■
ACC Conditions and Limitations
1
ACC Conditions and Limitations
If you need the radar sensor to be repaired, or
removed, or the radar sensor cover is strongly
impacted, turn off the system by pressing the
MAIN
button and take your vehicle to a dealer.
Have your vehicle checked by a dealer if you find any
unusual behavior of the system (e.g., the warning
message appears too frequently).
452
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Driving
■
Detection limitations
•
A vehicle suddenly crosses in front of you.
•
The interval between your vehicle and the vehicle ahead of you is too short.
•
A vehicle cuts in front of you at a slow speed, and it brakes suddenly.
•
When you accelerate rapidly and approach the vehicle ahead of you at high
speed.
•
The vehicle ahead of you is a motorcycle, bicycle, mobility scooter, or other small
vehicle.
•
When there are animals in front of your vehicle.
•
When you drive on a curved or winding or undulating road that makes it difficult
for the sensor to properly detect a vehicle in front of you.
•
The speed difference between your vehicle and a vehicle in front of you is
significantly large.
•
An oncoming vehicle suddenly comes in front of you.
•
Your vehicle abruptly crosses over in front of an oncoming vehicle.
453
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Continued
Driving
•
When driving through a narrow metal bridge.
•
When the vehicle ahead of you brakes suddenly.
•
When the vehicle ahead of you has a unique shape.
•
When your vehicle or the vehicle ahead of you is driving on one edge of the lane.
Sensor detects upper section of
an empty carrier truck.
Panel truck,
tanker truck, etc.
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
454
Driving
Increase or decrease the vehicle speed using the
RES/+
or
−/SET
buttons on the
steering wheel.
•
Each time you press the button, the vehicle speed is increased or decreased by
about 1 mph or 1 km/h accordingly.
•
If you keep the button pressed, the vehicle speed increases or decreases by about
5 mph or 5 km/h accordingly.
Press the
(Interval) button to change the
ACC following-interval.
Each time you press the button, the following-
interval (the interval behind a vehicle detected
ahead of you) setting cycles through short,
middle, long, and extra long following-
interval.
■
To Adjust the Vehicle Speed
1
If a vehicle detected ahead is going at a speed slower
than your increased set speed, ACC may not
accelerate your vehicle. This is to maintain the set
interval between your vehicle and the vehicle ahead.
You can switch the displayed set speed
measurements on the driver information interface
between mph and km/h.
2
P. 117
You can set the vehicle speed using the
−/SET
button
on the steering wheel when adjusting the speed with
the accelerator and brake pedals.
■
To Set or Change Following-interval
To increase speed
To decrease speed
Interval Button
455
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Continued
Driving
Determine the most appropriate following-interval setting based on your specific
driving conditions. Be sure to adhere to any following-interval requirements set by
local regulation.
The higher vehicle's following-speed is, the longer the short, middle, long or extra
long following-interval becomes. See the following examples for your reference.
Following-interval
When the Set Speed is:
50 mph (80 km/h)
65 mph (104 km/h)
Short
83 feet
25 meters
1.1 sec
100 feet
31 meters
1.1 sec
Middle
110 feet
33 meters
1.5 sec
137 feet
42 meters
1.5 sec
Long
154 feet
47 meters
2.1 sec
200 feet
61 meters
2.1 sec
Extra
Long
204 feet
62 meters
2.8 sec
265 feet
81 meters
2.8 sec
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
456
Driving
To cancel ACC, do any of the following:
•
Press the
CANCEL
button.
•
Press the
MAIN
button.
u
ACC indicator goes off.
•
Depress the brake pedal while the vehicle is
moving forward.
■
Automatic cancellation
The beeper sounds and a message appears on the driver information interface when
ACC is automatically canceled. Any of these conditions may cause the ACC to
automatically cancel:
•
Bad weather (rain, fog, snow, etc.).
•
When the radar sensor behind the emblem gets dirty.
•
The vehicle ahead of you cannot be detected.
•
An abnormal tire condition is detected, or the tires are skidding.
•
Driving on a mountainous road, or driving off road for extended periods.
•
Abrupt steering wheel movement.
•
When the ABS, VSA
®
, or CMBS
TM
is activated.
•
When the ABS or VSA
®
system indicator comes on.
•
When you manually apply the parking brake.
•
When the detected vehicle within the ACC range is too close to your vehicle.
•
The camera behind the rearview mirror, or the area around the camera, including
the windshield, gets dirty.
■
To Cancel
1
Resuming the prior set speed: After you have
canceled ACC, you can resume the prior set speed
while it is still displayed. Press the
RES/+
button
when driving at a speed of at least 25 mph (40 km/h)
or more.
The set speed cannot be set or resumed when ACC
has been turned off using the
MAIN
button. Press
the
MAIN
button to activate the system, then set the
desired speed.
CANCEL
Button
MAIN
Button
1
Even though ACC has been automatically canceled,
you can still resume the prior set speed. Wait until the
condition that caused ACC to cancel improves, then
press the
RES/+
button.
Continued
457
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
Driving
Press and hold the (interval) button for one
second.
Cruise Mode Selected
appears on
the driver information interface for two
seconds, and then the mode switches to
Cruise.
To switch back to ACC, press and hold the
button again for one second.
■
When to use
Desired speed in a range above roughly 25 mph (40 km/h).
Take your foot off the pedal and press the
–/SET
button when you reach the desired
speed.
The moment you release the
–/SET
button, the set speed is fixed, and cruise control
begins. The
CRUISE CONTROL
indicator comes on.
Each time you press the
RES/+
or
–/SET
button, the vehicle speed is increased or
decreased by about 1 mph (1.6 km/h).
If you keep the
RES/+
or
–/SET
button pressed, the vehicle speed increases or
decreases until you release it. This speed is then set.
■
To Switch ACC to Cruise Control
1
To Switch ACC to Cruise Control
Always be aware which mode you are in. When you
are driving in Cruise mode, the system will not assist
you to maintain a following-interval from a vehicle
ahead of you.
ACC ON
Cruise
Control ON
■
To Set the Vehicle Speed
■
To Adjust the Vehicle Speed
uu
Honda Sensing
®
u
Adaptive Cruise Control (ACC)
458
Driving
To cancel cruise control, do any of the following:
•
Press the
CANCEL
button.
•
Press the
MAIN
button.
•
Depress the brake pedal.
The
CRUISE CONTROL
indicator goes off.
■
To Cancel
1
Resuming the prior set speed:
After cruise control has been canceled, you can still
resume the prior set speed by pressing the
RES/+
button while driving at a speed of at least 25 mph (40
km/h) or more.
You cannot set or resume in the following situations:
•
When vehicle speed is less than 25 mph (40 km/h).
•
When the
MAIN
button is turned off.
At vehicle speeds of 22 mph (35 km/h) or less, cruise
control is canceled automatically.
459
uu
Honda Sensing
®
u
Lane Keeping Assist System (LKAS)
Continued
Driving
Lane Keeping Assist System (LKAS)
Provides steering input to help keep the vehicle in the middle of a detected lane and
provides tactile and visual alerts if the vehicle is detected drifting out of its lane.
1
Lane Keeping Assist System (LKAS)
Important Safety Reminders
The LKAS is for your convenience only. It is not an
autonomous driving system and always requires
driver attention and control. The system does not
work if you take your hands off the steering wheel or
fail to steer the vehicle.
2
Driver Information Interface Warning and
Information Messages
P. 96
The LKAS is convenient when it is used on
expressways or freeways.
Do not place objects on the instrument panel.
Objects may reflect on the windshield and prevent
correct detection of the traffic lanes.
The LKAS only alerts you when lane drift is detected
without a turn signal in use. The LKAS may not detect
all lane markings or lane departures; accuracy will
vary based on weather, speed, and lane marker
condition. It is always your responsibility to safely
operate the vehicle and avoid collisions.
The LKAS may not work properly or may work
improperly under the certain conditions:
2
LKAS Conditions and Limitations
The LKAS may not function as designed while driving
in frequent stop and go traffic, or on roads with
sharp curves.
When you operate the turn signals to change lanes, the system is suspended, and
resumes after the signals are off.
If you make a lane change without operating the turn signals, the LKAS alerts
activate, and torque is applied to the steering.
■
Front sensor camera
Monitors the lane
lines
■
Tactile and visual alerts
Rapid vibrations on the steering wheel
and a warning display alert you that the
vehicle is drifting out of a detected
lane.
■
Steering input assist
The system applies torque to the steering to keep the vehicle between the left and
right lane lines. The applied torque becomes stronger as the vehicle gets closer to
either of the lane lines.
uu
Honda Sensing
®
u
Lane Keeping Assist System (LKAS)
460
Driving
Provides assistance to keep the vehicle in the center of the lane. When the vehicle
nears a white or yellow line, steering force of the electric power steering will become
stronger.
When the vehicle enters the warning area, the LKAS alerts you with slight steering
wheel vibration as well as warning display.
■
Lane Keep Support Function
1
Lane Keeping Assist System (LKAS)
You can read about handling information for the
camera equipped with this system.
2
P. 473
When it fails to detect lanes, the system will
temporarily be canceled. When a lane is detected, the
system will recover automatically.
■
Lane Departure Warning Function
Warning Area
Warning Area
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст