Mitsubishi Colt Ralliart. Manual — part 459
GROUP 32
POWER PLANT
MOUNT
CONTENTS
GENERAL INFORMATION . . . . . . . .
SERVICE SPECIFICATIONS. . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ENGINE MOUNTING . . . . . . . . . . . . .
REMOVAL AND INSTALLATION <4A9> . .
REMOVAL AND INSTALLATION <4G1> . .
TRANSMISSION MOUNTING . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
ENGINE ROLL STOPPER ROD. . . . .
REMOVAL AND INSTALLATION . . . . . . . .
FRONT AXLE CROSSMEMBER . . . .
REMOVAL AND INSTALLATION <4A9> . .
REMOVAL AND INSTALLATION <4G1> . .
Main
Index
GENERAL INFORMATION
POWER PLANT MOUNT
32-2
GENERAL INFORMATION
M1321000100953
An inertia main shaft 3-point support type has been
adopted as an engine mount system, which has the
following features.
• By optimising the 3-point mount layout, the idling
vibration and acceleration noise are decreased
drastically.
• The transmission mounting insulator is built into
the body side member in order to absorb the
vibration transmitted from the engine efficiently.
• By connecting the engine roll stopper rod assem-
bly to the high-rigidity front axle No.1 crossmem-
ber, the vibration transmitted from the engine is
decreased.
CONSTRUCTION DIAGRAM
AC601523
AC402550
AC601316
AC601382
AC601383
<4A9>
<4G1>
AB
Engine mounting
insulator <CVT>
Engine mounting insulator
Transmission
mounting
insulator <CVT>
Transmission
mounting insulator
Front axle No.1
crossmember
Front axle No.1
crossmember
Engine roll stopper
rod assembly
Engine mounting
insulator <M/T>
Transmission
mounting
insulator <M/T>
Engine roll stopper
rod assembly
Main
Index
Group
TOC
SERVICE SPECIFICATIONS
POWER PLANT MOUNT
32-3
SERVICE SPECIFICATIONS
M1321000300548
Item
Standard value
Protruding length of stabilizer bar bolt thread part mm
4A9
19
± 1.5
Protruding length of stabilizer link assembly thread part mm
4G1
5
± 1.5
SPECIAL TOOLS
M1321000600709
Tool
Number
Name
Use
MB991897
MB991897 or
MB992011
Ball joint remover
<4A9>
• Knuckle and tie rod end ball
joint disconnection
• Knuckle and lower arm ball
joint disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113) is also
available to disconnect ball joint.
B991113
MB991113
Steering linkage
puller
<4G1>
• Knuckle and tie rod end ball
joint disconnection
• Knuckle and lower arm ball
joint disconnection
Main
Index
Group
TOC
ENGINE MOUNTING
POWER PLANT MOUNT
32-4
ENGINE MOUNTING
REMOVAL AND INSTALLATION <4A9>
M1321001101302
Pre-removal Operation
Raise the engine and transmission assembly until its weight
is not applied to the insulator, and support it securely.
<M/T>
AC601315AB
68 ± 7 N·m
3
4
5
20 ± 5 N·m
2
N
68 ± 7 N·m
1
5.0 ± 1.0 N·m
68 ± 7 N·m
Removal steps
>>
A
<<
1.
Earth cable connection
2.
Self-locking nut
3.
Engine mounting insulator and
dynamic damper assembly
4.
Engine mounting bracket dynamic
damper
5.
Engine mounting insulator
Removal steps (Continued)
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст