Mitsubishi Colt Ralliart. Manual — part 286
AK102750
TRANSMISSION
CONTINUOUSLY VARIABLE TRANSMISSION OVERHAUL
23B-17
37.Remove the O-ring shown in the illustration from
the transmission case.
AK102749
38.Remove the reaction shaft support from the
transmission case.
AK102747
39.Remove the thrust washer from the forward
clutch.
NOTE: The thrust washer may attach to the reac-
tion shaft support which was removed in the pre-
ceding step.
AK102746
40.Remove the knock pin that is positioning the
manual control shaft from the transmission case.
AK102940
41.Remove the manual control shaft and parking
roller rod from the transmission case.
AK102743
42.Remove the parking roller support shafts (two
pieces) from the transmission case.
AK102742
43.Remove the parking roller support from the
transmission case.
Main
Index
Group
TOC
AK102741
TRANSMISSION
CONTINUOUSLY VARIABLE TRANSMISSION OVERHAUL
23B-18
44.Remove the parking sprag shaft, then remove the
parking sprag and spring from the transmission
case.
AK102740
45.Remove the forward clutch and input shaft out of
the transmission case.
AK102739
46.Remove the planetary carrier out of the
transmission case.
AK102737
47.Remove the reverse brake out of the transmission
case.
AK102735
48.Remove the oil guide from the transmission case.
AK102734
49.Remove the belt lubricating pipe out of the
transmission case.
Main
Index
Group
TOC
TRANSMISSION
CONTINUOUSLY VARIABLE TRANSMISSION OVERHAUL
23B-19
REASSEMBLY SERVICE POINTS
CAUTION
• Do not reuse any of the removed gaskets,
O-rings and oil seals. Be sure to use new gas-
kets, O-rings and oil seals when the transmis-
sion is reassembled.
• Only blue petrolatum jelly and white Vaseline
may be used during assembly.
• The friction elements and the parts having
surfaces on which other parts rotate or slide
must be coated with ATF before they are
assembled. New brake and clutch discs must
be immersed in ATF for more than two hours
before installation.
• Do not apply sealant and adhesive to any pre-
formed gaskets.
• If a bushing requires replacement, replace the
assembly which includes the bushing.
• Do not use cotton gloves and shop towel or
rag during assembly work. Use nylon gloves
and paper towel if necessary.
•
AK202428
MD998800
AC
Do not forget to change the fluid in the oil
cooler.
1. Install a new oil seal in the transmission case
using the special tool Oil seal installer
(MD998800).
AK102734
2. Install the belt libricating pipe in the transmission
case.
AK102735
3. Install the oil guide on the transmission case.
AK102736
4. Turn the flats of the reverse brake bearing to the
positions indicated in the illustration.
AK102737
5. Install the reverse brake in the transmission case
while aligning the oil pipe and knock pin positions.
AK204083AC
Thrust
bearing
Planetary
carrier
6. Install the thrust bearing into the planetary carrier
in the direction shown in the illustration.
Main
Index
Group
TOC
AK102739
TRANSMISSION
CONTINUOUSLY VARIABLE TRANSMISSION OVERHAUL
23B-20
7. Install the planetary carrier in the transmission
case.
AK102740
8. Install the input shaft and forward clutch in the
transmission case.
AK102741
9. Install the parking sprag and spring in the
transmission case, then install the parking sprag
shaft.
AK102742
10.Install the parking roller support on the
transmission case.
AK102743
11.Install the parking roller support shafts (two
pieces) in the transmission case.
AK102744
12.Install the manual control shaft and parking roller
rod on the transmission case.
AK302791AC
13.Push the manual control shaft in the direction
indicated in the illustration, then fit the new
O-rings (two pieces) in the O-ring groove.
AK102746
14.Install the knock pin for positioning the manual
control shaft in the transmission case.
Main
Index
Group
TOC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст